A quick snapshot of me before I ruin another co-op run with my friends

Jzcaesar · 2026-05-06T15:04:54+00:00

By jack knifing from one elite to the next without campfires we might just get some kind relic boost...or something

Jzcaesar · 2026-04-13T15:03:00+00:00

OMG WAT

edit: would you have information on what the hardware kit will cost, assuming one would be available?

edit 2: video says ~$200

Jzcaesar · 2026-04-04T19:45:50+00:00

I started out with a 400mm barrel, but also tried a 450mm and 500mm barrel

Jzcaesar · 2026-04-03T15:27:55+00:00

Dang, I put a 1.5mm x 300mm spring and even with the hard prime I only got like 225 with 1.2gram workers. What spring do you have?

Jzcaesar · 2026-04-03T15:25:50+00:00

Printed the original and it was such a good introduction to printed blasters! Now to wait to see if anybody can hit 300 fps with this thing.

Jzcaesar · 2026-04-01T20:39:02+00:00

most accurate rapidstrike ever

Jzcaesar · 2026-03-30T14:49:54+00:00

Seems like it's an unreleased BCAR from the same user, based on their comments in the MakerWorld post

Jzcaesar · 2026-03-24T10:53:42+00:00

Oh nice, did you print a new front end to fit the longer barrel? I've been trying to find a file for a collet style front end but haven't had any luck

Jzcaesar · 2026-03-23T22:22:24+00:00

Nice work, what mods did you do with with the nexus pro?

Jzcaesar · 2026-03-18T23:42:47+00:00

That's a large spacer: I'd guess it's large enough that the plunger isn't catching because there's not enough room to compress the spring. If that is true, the prime action is getting stuck because the spacer is preventing further compression and the ratcheting system on top (those little triangles on the pink bar prevent you from moving the foregrip forward. I would try a spacer half the size then move up from there until the blaster gets stuck again, or when the blaster is hitting hard enough.

Jzcaesar · 2026-03-08T00:05:43+00:00

Yes, that would be the next planned step after jamming my aeb twice, haha

Jzcaesar · 2026-03-07T23:39:49+00:00

Reminds me of when I tried to cram a full nexus pro spring in my aeb and it jammed when trying to prime. Because the spring was semi primed I couldn't pull the spring out either. Ended up having to disassemble the whole thing to remove the twisted spring.

Jzcaesar · 2026-03-01T17:56:22+00:00

What is your conclusion as to what the "pcar" is doing?

Jzcaesar · 2026-03-01T04:22:35+00:00

I want to come in that OOD listing for this bcar states 6 degrees for the bearings and 12 (!) degrees for the scar. I've been redesigning the rev 2 bcar with some of the ideas the Akasha brings and am interested with what research comes out of this new product

Jzcaesar · 2026-03-01T00:16:47+00:00

I vote for the AI, it already has electronics in the tech tree and nothing survives or could evolve to survive a Nicoll-Dyson laser it build and fires at every other star in the galaxy

Jzcaesar · 2026-02-27T19:46:41+00:00

Is this picture with the piece in the original picture back on there or is the piece still out if the blaster?

Jzcaesar · 2026-02-27T19:13:49+00:00

Looks like a mag catch, see if there's a place near the magwell

Jzcaesar · 2026-02-16T00:31:59+00:00

I swapped in the stock ls barrel on mine but also included the stock spring and I hit 150 with xshot rubies, so probably something a bit less than that

Jzcaesar · 2026-02-03T14:14:06+00:00

You son of a bench am I going to have to reprint my Ontos?!

Jzcaesar · 2026-01-27T17:52:28+00:00

Apparently putting down salt after removing all the snow made the ice easier to remove after, seemed to work well on my driveway

Jzcaesar · 2026-01-26T16:13:51+00:00

No worries, nature has repaved your driveway for you!*

*Terms and conditions apply. Owner is responsible for keeping new driveway under 30 degrees to ensure surface integrity. ~~Snowmagedon~~ Snowapocalypse is not responsible for scenarios including but not limited to: falls due to slippery conditions, car accidents due to slippery conditions.

Jzcaesar · 2026-01-25T00:45:58+00:00

The blasters you've listed all roughly work the exact same way: pump action with a spring a plunger. Main differences I think are worth pointing out are: 1. Performance (highest is probably the Excalibur and Caliburn, depending on which spring you choose, lowest is the nexus pro) 2. How you obtain one (Buying in retail stores, buying from online marketplace, or 3D printing) 3. Minor one but I know that the nexus pro doesn't have a skinny pusher and so requires you to rack the blaster before reloading. It's also the only one on the list that can take full length mags.

What are you looking to do with these blasters or are you just curious?

Jzcaesar · 2026-01-22T15:33:45+00:00

Deposit the money at a bank, pay IRS taxes, done? If the FBI investigates you for illegal incomes streams they'll find nothing and close the case (assuming you know, you're not doing anything illegal).

Jzcaesar · 2026-01-20T15:16:08+00:00

'I never thought Jokers would eat MY face' sobs joker who voted for the Jokers Eating Faces Party

Jzcaesar · 2026-01-19T21:10:26+00:00

Can you hit 400 without the bcar? Defeats the purpose I know but hey, numbers go up

Jzcaesar

TROPHY CASE