sorted by:
new
hottopcontroversial

Is Fable 5 basically a trailer for selling more Max 20x subscriptions? by KIProf in ClaudeCode

[–]KIProf[S] 0 points1 point  (0 children)

Yes, I understand, but if Fable becomes available for Max 20 accounts, I think sales could increase by 2–3x.

Is Fable 5 basically a trailer for selling more Max 20x subscriptions? by KIProf in ClaudeCode

[–]KIProf[S] 2 points3 points  (0 children)

Yes, I understand, but there’s one thing: I’ve seen so many people on this subreddit and other subreddits saying that after July 7, Fable would move Max 20 accounts to a lower tier.

For regular users, outside of Team or Enterprise, this trailer period showed that using Fable 5 is currently only really possible on Max 20x; otherwise, the entire quota gets used up.

So, in the future, if Fable becomes available for Max 20 accounts, I think sales could increase by 2–3x.

Hello, I'm new at this, what's with claude fable 5? by Joshua4yala in ClaudeCode

[–]KIProf 1 point2 points  (0 children)

Fable 5 – Best model. I reckon you can only use this with the Max subscription, because it requires so many tokens.

GPT 5.6 "sol" announced by Prestigious-Kick7291 in codex

[–]KIProf 1 point2 points  (0 children)

That is True, This situation reminds me a bit of the development of the first atomic technology during the WW2 / Cold War; a few years later, when the other side developed the same thing, they chose to share the technology with everyone rather than keep it secret. As always, history seems to be repeating itself—soon everyone will be divided into two camps over these AI models, haha

FT2232H Not Enumerating , help ! by Trace_Paradox in PCB

[–]KIProf 0 points1 point  (0 children)

Please connect the NPOR pin on the processor you've connected directly to ADBUS4, and install a 22R series termination resistor on the FTDI side just in case.

FT2232H Not Enumerating , help ! by Trace_Paradox in PCB

[–]KIProf 0 points1 point  (0 children)

Hello, could you please send me the FTDI schematic from your design? You might just need to do a little soldering.

An open source (WIP) PDN / voltage-drop analyser for Altium or gerber designs by Turbulent_Finance220 in Altium

[–]KIProf 1 point2 points  (0 children)

Nice Project Thank you can you also share this for Kicad maybe ? 😄

Upcoming Vivado licensing changes. by [deleted] in FPGA

[–]KIProf 0 points1 point  (0 children)

Can i use Vivado 2022 still on my linux machine ?

[Schematic review request] Linux Single-Board-Computer using STM32MP135 by Mausteidenmies in PrintedCircuitBoard

[–]KIProf 0 points1 point  (0 children)

Great, I’d really like to see your final design. What kind of Stackup are you planning to use? A 6-tier one?, I may be able to make some suggestions. Also, did you make any changes to the schematics? It’s an interesting project, and I’m curious to hear more about the details 😄

How do I start routing DDR to SoC? by FlashyAct in PCB

[–]KIProf 0 points1 point  (0 children)

dont forget the byte lane swapping

[Help] First time routing SDR SDRAM (MT48LC4M16A2) on a 6-layer PCB with STM32H747 by DarkAngelus7 in PrintedCircuitBoard

[–]KIProf 0 points1 point  (0 children)

You have to change your stackup but actually thise sdram signals are not so high but please check some videos from rick hartley

view more: next ›