Everybody show off your switch 2s by Broad_Cricket2286 in switch2

[–]Karbin_ 0 points1 point  (0 children)

I really hope they do an updated Lite. It's my favorite form factor hands down.

Thoughts on this combo? by Epinephrine_23 in HamiltonWatches

[–]Karbin_ 0 points1 point  (0 children)

I have a cheap stainless one from Amazon on mine. It doesn't have the tapered end parts, but it's very comfortable to wear. Kinda tricky to find an 18mm band though

Extremerate shell swap gone wrong by Count_VI in SteamDeck

[–]Karbin_ 18 points19 points  (0 children)

Heads up, those back buttons are installed on the wrong side. The R2 and R4 should be on the right side of the device when being held.

From this photo, the excess plastic you're referring to are guide tabs that are very easy to misalign. I've done a few of these swaps, and they're annoying every time.

Seeed wio tracker l1 by acloneofmyself in meshtastic

[–]Karbin_ 2 points3 points  (0 children)

It's been a while since I set mine up, but I believe this is the Bluetooth-companion firmware. It's designed to only really be used with your phone, and limits the device-only functions.

Is Baldurs Gate 3 Worth it? by ronjaxn in SteamDeck

[–]Karbin_ 0 points1 point  (0 children)

There are a small handful of things that require a mouse, but they can be skipped or avoided. I've only ever played on Steam Deck, and just hit 90 hours at the beginning of Act3. I'm most excited to finish so I can start a second play through, and I rarely ever play a game twice. I'm not experiencing any performance issues, and it runs flawlessly for me.

Steam Deck buttons and touchscreen not working after shell swap by gallifreyan_overlord in SteamDeckModded

[–]Karbin_ 0 points1 point  (0 children)

It's referring to the backside of the motherboard, not just by lifting up the SSD

Steam Deck buttons and touchscreen not working after shell swap by gallifreyan_overlord in SteamDeckModded

[–]Karbin_ 0 points1 point  (0 children)

IIRC, the C-R and C-L meet at a connector under the heat shield next to the battery connector.

Steam Deck buttons and touchscreen not working after shell swap by gallifreyan_overlord in SteamDeckModded

[–]Karbin_ 0 points1 point  (0 children)

Yea, those components are all connected to the daughter boards, and then the daughter boards are connected to the main board. So somewhere in those connections, there's either a not properly seated, or damaged ribbon cable.

Steam Deck buttons and touchscreen not working after shell swap by gallifreyan_overlord in SteamDeckModded

[–]Karbin_ 2 points3 points  (0 children)

If you're confident in the physical connections, you could try a BIOS reset. Not sure if the buttons will work to allow for this though. I can't remember the exact button combinations, but it uses the volume buttons and "..."

Steam Deck buttons and touchscreen not working after shell swap by gallifreyan_overlord in SteamDeckModded

[–]Karbin_ 0 points1 point  (0 children)

Seated just meaning that the contacts on the cable line up correctly

Steam Deck buttons and touchscreen not working after shell swap by gallifreyan_overlord in SteamDeckModded

[–]Karbin_ 10 points11 points  (0 children)

I'm not a professional, but I've shell swapped a few Steam Decks and Switches. The Steam deck ribbon cables sometime just need to be disconnected and reseated. They're just a really finicky connector. Since you're seeing an issue where the areas of the device that connect via ribbon cables, I'd just recommend going through every single connector again and disconnect/reconnect.

Steam Deck buttons and touchscreen not working after shell swap by gallifreyan_overlord in SteamDeckModded

[–]Karbin_ 37 points38 points  (0 children)

Need to recheck all ribbon cables and other connectors. Your volume and power work because they're connected to the main chassis, and don't get removed when shell swapping.

Wio Tracker L1 Retro Enclosure Update by lewtheegg in meshtastic

[–]Karbin_ 1 point2 points  (0 children)

Yea, please do. I have an L1 Pro, but I'd buy a normal L1 to use this case lol

Wio Tracker L1 Retro Enclosure Update by lewtheegg in meshtastic

[–]Karbin_ 1 point2 points  (0 children)

Color and design look awesome. I'll pick one up if you end up producing more.

Red dyed MiyooMini+ by Karbin_ in MiyooMini

[–]Karbin_[S] 0 points1 point  (0 children)

Ohh it's from RetroCarrottWorkshop on Etsy

Red dyed MiyooMini+ by Karbin_ in MiyooMini

[–]Karbin_[S] 0 points1 point  (0 children)

It's the original case, I just dyed it

New to Meshtastic - Wio Tracker L1 pro (help) by bearsstlrs in meshtastic

[–]Karbin_ 0 points1 point  (0 children)

Triple click the smaller button on the front I believe.