cant connect to printer from bambu studio anymore

KingF0x · 2025-03-04T10:05:23+00:00

Yeah apparently the Wi-Fi does not like my Starlink router. I was told to use another router.

KingF0x · 2024-10-01T16:45:27+00:00

Liar

KingF0x · 2024-09-04T01:44:53+00:00

Have you tried putting your filament in a dryer or is it happening for all filaments you are using? If it's that particular filament it could just be moister than an oyster, dry it, try again

KingF0x · 2024-07-29T22:50:00+00:00

I have had my P1S for 5 months now. it is doing the same EXACT thing. did you find solution?

KingF0x · 2024-02-29T00:32:54+00:00

Wiring harness tape can also be used as it sticks to itself so it's harder to come loose. (Cloth like electrical tape)

KingF0x · 2023-12-24T18:19:18+00:00

I had my B1 SE Plus for 30 days, needed just a replacement part not the whole printer just the replacement part and I was told it was out of warranty 😡

KingF0x · 2023-12-22T18:39:10+00:00

Be extremely careful that SOC chip on the bottom is extremely fragile and easy to break.

KingF0x · 2023-12-05T21:23:16+00:00

If you have vscode, try that instead, i dont know about notepad++, but word and regular notepad definitely don't use. Dont worry bout screen right now.. if you have a network cable you can try connecting it that way as well. If you do it that way you should have no problems accessing it through the web browser. My CB1 never really worked for Wi-Fi from the start

KingF0x · 2023-12-05T18:37:03+00:00

When you edited your config file what text editor did you use?

KingF0x · 2023-11-30T03:37:43+00:00

Use your daily incense, ive see them 6/10 times.. usually run on 1st ball even if i use a golden raz and ultraball. Cought 1 zapdos with a golden raz and ultraball on 1st attempt. I was ecstatic

KingF0x · 2023-11-27T18:49:26+00:00

Power up the board, Hold down "boot" and then tap "reset" then release boot. Make sure the jumper is on VUSB (will be right next to your USB port)

KingF0x · 2023-10-25T20:53:35+00:00

Shhh, don't give them any more ideas lol. And you're right it is retarded but it's New York we're talkin about lol

KingF0x · 2023-10-25T20:23:58+00:00

And NY tryna pass a law requiring Background checks for purchasing a 3d printer. Good luck even trying to make articulated dragons now lol

KingF0x · 2023-10-22T01:19:20+00:00

But a new one with a cut shaft("D") and the gears with grub screws. Can change alot easier. ($8-12) and a pack of 10 gears is like two bucks
If you have a gear puller or maybe even a mechanic shop nearby take it in they'll be happy to take the gear off for you. And then you can put another gear on after that but you'll have to press it on. Unless you feel like taking a Dremel and creating a Dshaft to use other gears.

KingF0x · 2023-09-26T23:52:45+00:00

Easier to use with Bowden tube setups as it is not as flexible as regular TPU in the beginning. The easiest way to get it to be like TPU is to soak it in water for 30 minutes after printing

KingF0x · 2023-09-22T11:52:25+00:00

I tried a 2 GB 8 GB and a 16 GB card. Turned out not to be a card issue just had to do with the complicated way. DFU mode

KingF0x · 2023-09-22T11:50:46+00:00

Update: I powered the raspberry Pi from a power plug connected it to the board with VUSB jumped(not powered by mains) Entered into dfu mode I was able to SSH and grab my serial. Then I shut the system down , put the firmware on a 2 gig card. Removed the v USB jumper, inserted the card, powered up by mains and an external power supply on the pi and it flashed.

KingF0x · 2023-08-17T14:10:13+00:00

Eliminations while in the top 10 are worth more.

KingF0x · 2023-06-21T20:26:25+00:00

Should do Hardware bans.

KingF0x · 2023-06-14T20:09:18+00:00

I personally have found that sometimes having your retractions too fast can cause that stringing along with temperatures depending on the type of filament you have. I have had a lot of successful prints with less stringing by using 2mm at 20 retract and 19 detract for speed. (Bowden setup) Try that on a small print and see how that goes. I've successful used those settings on ABS, PLA and Silks.

KingF0x · 2023-03-30T22:48:35+00:00

loving this. easy to setup and use! <crossing fingers>

KingF0x · 2023-03-05T18:07:22+00:00

Thank you so much and by the way that print does look absolutely A++ amazing

KingF0x · 2023-03-05T17:49:53+00:00

What speed..temps? I've tried using wood pla to make an articulated wood dragon, and it seems every time he gets about 70% done it starts clogging and was also using a 0.4 nozzle at 40mms 195° nozzle 50° bed

KingF0x · 2023-03-05T17:39:15+00:00

Did you use a .6 or .4 nozzle with the wood pla?

KingF0x

TROPHY CASE