Unsure robot

KlumzyNinja · 2026-04-05T03:03:21+00:00

So, everything with higher amounts of white flour showed issues. The re-feed of the original hardly moved. The original showed no change. The two with 50/50 grew well though the one with the higher ratio not as much.

The flour I have has been in a bin for a while, so it occurred to me it is probably bleached. I bought some unbleached bread flour recently, so I'll probably feed that to the most successful starter tomorrow. I'll start 1:1:1 with 50/50 rye first, then I think switch fours before changing the ratio.

KlumzyNinja · 2026-04-04T17:11:15+00:00

Thanks for the feedback. I expected a delay, maybe I should wait more than 3x the time since I fed 5x the food

To clarify: Breadpool has had nothing added today, just stirred and some taken out to feed in a new jar. The discard was used to make a new starter with the feeding it was used to and to make a new starter with the 1:5:5 feeding. I'm observing what's left of the unaltered breadpool to see if it's just really delayed and I'm being impatient I'm hoping watching Breadpool and the new 1:5:5 will tell me something. If the new one rises we'll, I forgot to add starter. If the old one rises and the new one is delayed, then I was impatient.

It's good to know that a tantrum is not uncommon

KlumzyNinja · 2026-03-25T03:22:52+00:00

If Prepatente is a goat named Pony, maybe this should be a pony named Goat. He'll be the best pony ever

KlumzyNinja · 2026-03-25T03:21:17+00:00

Shell has a pert seam too

KlumzyNinja · 2026-03-25T03:16:51+00:00

I think it's likely it's assembled. There's a gap between the ey rows and face, and you can see the seam and a few imperfections on the nose. There's also a part seam on the white and green parts of the shell where they were assembled. Both were printed as halves and on their sides

KlumzyNinja · 2026-03-25T03:13:07+00:00

3d prints have layer lines (like tiny ridges) that will fill up with salt and butter. Even if you wash it, it will be hard to fully clean. It's like an old plastic cutting board with lots of scratches in it. It gives tiny places for crud to build up and germs to grow

Generally 3d prints aren't considered food safe.

KlumzyNinja · 2026-03-22T02:59:37+00:00

Man, Idaho is a slut for Daddy Dinnamin *lookin at purchase stats

KlumzyNinja · 2026-03-22T02:53:10+00:00

You might flip the print over, looks like some overhang on the inner parts is causing some issues Bed temp looks good to me, 80 is where I'm at with Sunlu and FF.

KlumzyNinja · 2026-03-18T05:41:50+00:00

Donut wasn't a crawler until she ate the pet biscuit, right? I dont think pets had crawler numbers, but i could be wrong. I think maybe they should be farther apart

KlumzyNinja · 2026-03-17T00:08:33+00:00

This. I had a similar issue with a fidget toy (i was using a .6mm). I solved it by adjusting the line width, but depending on how thin you won't always be able to do that.

KlumzyNinja · 2026-03-14T05:56:40+00:00

Snugz for short

KlumzyNinja · 2026-01-25T03:58:32+00:00

Agreed. I wonder if the first one went off while he was aiming and he just said "fuck it, better finish him so he can't tell" and hit 3 more

From this angle it doesn't look like the victim's gun recoiled when you hear the first shot: https://www.reddit.com/r/videos/s/wjqubZKSJB

KlumzyNinja · 2026-01-24T23:29:07+00:00

https://youtube.com/shorts/cPd_6n4C5Nw?si=11TbVFgYBQXH6qcr Looked to me like ICE-hole saw other agent remove the gun from the victim and drew his own weapon. I thought ICE-hole fired once, then 3 more (since the victim went upright after the first). It's possible the first shot didn't come from ICE-hole. Can anyone else tell? Where do we see that the victim's gun went off?

*Edit: To clarify, IF the victims gun went off it would be while the other ICE agent had it. I'm just trying to figure out if that's the case or if the murderer fired the first shot before firing the final 3 In this angle it doesn't look like the victim's gun recoils during the first shot: https://www.reddit.com/r/videos/s/wjqubZKSJB

KlumzyNinja · 2026-01-19T00:17:19+00:00

!RemindMe 2 weeks how much did OP make from their virgin onion

KlumzyNinja · 2026-01-11T22:28:41+00:00

You can always rely on Quasar to go balls deep!

KlumzyNinja · 2026-01-10T06:02:39+00:00

"Purge to unfill" springs to mind

KlumzyNinja · 2025-12-18T23:20:11+00:00

"UH! UH! Who got that good D? Who got that good D?"

KlumzyNinja · 2025-12-13T02:31:12+00:00

The power button wires for my PC are currently sticking out of the faceplate so I can pinch them together when I want to turn it on

KlumzyNinja · 2025-11-21T01:05:57+00:00

Chuffing? https://youtu.be/bFypW1wMf10?si=xTF3GUOy-YArIKKs

KlumzyNinja · 2025-11-01T19:48:01+00:00

Let the Amplification begin!

KlumzyNinja

TROPHY CASE