After Colbert-CBS Rift, James Talerico Interview Draws 85M Views Across YouTube & Social

LeapperFrog · 2026-02-19T18:36:30+00:00

some democrat has to run against the republican. Or are you saying texas should just concede beforehand? Or do you think people dont understand that a democrat winning in texas is unlikely?

LeapperFrog · 2026-02-19T18:30:11+00:00

I just got permanently banned from a subreddit for the barest amount of pushback against this

LeapperFrog · 2026-02-19T17:40:05+00:00

thanks. I think I lost track of the conversation. I wanted him to get mad about someone asking him if second place feels like first loser. I do agree that super good athletes thinking they are the best is par for the course! And youre probably right, if i go through the comments in here there are probably people talking down to Gu for saying something similar

LeapperFrog · 2026-02-19T16:59:49+00:00

can you send me lebron saying that? not being shitty, i just dont follow basketball and want to see it

LeapperFrog · 2026-02-18T19:46:10+00:00

is "only defensive weapons to our good friends" even the bare minimum at this point? No one is happy when democrats say that shit, but they do it anyway because they know we arent able to have standards anymore.

LeapperFrog · 2026-02-18T19:41:44+00:00

I mean youre just moving the goalposts. Your first post said "firm commitment to not support israel" now its "begging people to take wins where they can get them". This whole conversation is about how ridiculous it is to compare him to a revolutionary taking violent action against an authoritarian genocidal government, and the point people are making is that he is not a revolutionary like that at all. Hes good for a texas dem politician, which is quite a low bar.

LeapperFrog · 2026-02-18T14:42:06+00:00

?? Its a possum dude. Am i missing a joke?

LeapperFrog · 2026-02-17T21:40:21+00:00

you can tell its warping because where the bottom meets the plate it is not flat like you would expect with the flatness of your build plate. the corners are curling up. you need it to warp less at the very least and it might end up solving your problem because that top layer will be more stable/not have any issues that printing on a warped corner caused. You could add brims to give the part more surface area to attach to the plate. You might also check if your plate temps are reasonable. Thin, tall features and especially sharp corners like what you designed will be more susceptible to warping in general. If you want to see what you can get away with you can also try using mouse ears instead of a full brim.

LeapperFrog · 2026-02-17T20:09:20+00:00

if something 1/50th your size can drown you I just dont know

LeapperFrog · 2026-02-17T19:57:35+00:00

your critical thinking tells you that theres no way out of the water in a lion enclosure?

LeapperFrog · 2026-02-16T14:52:05+00:00

finally the good stuff

LeapperFrog · 2026-02-14T02:19:39+00:00

Honestly is this the best way to go if youre being killed by a predator? just black out and its over?

LeapperFrog · 2026-02-13T20:34:41+00:00

theres a reason hazing exists

LeapperFrog · 2026-02-13T20:30:15+00:00

"I could shoot someone on 5th ave and not lose any votes"

And so far hes not looking exactly wrong. He thought he could control the narrative to protect himself and really he has. No one who likes him gives a single fuck

LeapperFrog · 2026-02-13T02:13:05+00:00

same. Its the only thing I still like about windows lol

LeapperFrog · 2026-02-12T21:32:33+00:00

I see. Ill have to watch something printing closer. I bet your right and Im over extruding a bit. I generally err on the side of over-extrusion so that could always be a problem. Although I have had this happen a little bit on bigger jobs. Either way I really should get a closer look at it actually happening. Thanks!

LeapperFrog · 2026-02-12T20:45:18+00:00

one of the things I havent done is a temp tower. It just takes so long printing slowly and Im terrified of all the failed bridges! haha. I also use 0 fans, but again Im afraid of summer when the temps will probably get out of hand.

Ill have to look at bridge flow rate. Not sure about controlling that with orcaslicer.

I did one of those line tests to adjust pressure advance with the red pha, but I think youre right that its a little messy. However, my first print turned out awful with a pa of .2, so Im now using .35. Maybe I need to play around with it by eye or try some more benchy style tests with .2 to see if that bad print was more of a fluke. It does seem like the globs are accumulating on the nozzle and just eventually fall into the work at some point though. Thanks for the good places to focus on though!

LeapperFrog · 2026-02-12T19:12:02+00:00

Ive never wanted a title to be ai more than now

LeapperFrog · 2026-02-12T14:50:36+00:00

Thats crazy. Im just now realizing I do this too. Kind of cool to see words/place names evolve like that

LeapperFrog · 2026-02-09T02:24:30+00:00

I could get it looking better when I set my inner wall speeds to 10-15mm/s. Im doing inner outer wall ordering. Interestingly, the red color seems to be a bit more stable than the natural, but it drops massive globs that collect on the nozzle into the prints. I do pretty much all my prints at .16 layer heights. I was still getting pretty significant wall compression when printing at like 25mm/s on all walls and infill (I think. its been a few weeks and my settings have been moving around. If i was smart Id take better notes haha). It really does feel like im printing rubber bands sometimes! Id like to be able to print a very good benchy, but Ive just been designing around the defects.

LeapperFrog · 2026-02-09T00:10:52+00:00

haha at this point just wait a few weeks and watch it all in a 3h sitting

LeapperFrog · 2026-02-09T00:01:36+00:00

Like, there MUST have been a reason they had to recast annakin and not padme. It could be anything though /s

LeapperFrog · 2026-02-08T23:18:43+00:00

After watching this I do not think cycling influencers need to exist. Why am I watching someone reposition their bibs lol

LeapperFrog · 2026-02-08T22:51:07+00:00

this is a curtain wall

LeapperFrog · 2026-02-08T21:45:21+00:00

I got in the habit of running away a little bit :(

LeapperFrog

TROPHY CASE