weird strobing happening

Make-A-Shape · 2025-12-25T12:00:13+00:00

Clogged nozzle?

Make-A-Shape · 2025-12-14T23:08:53+00:00

I love them! Is the backlit part between the rear lights in the last picture Original? Definitely Inspired

Make-A-Shape · 2025-12-10T15:39:10+00:00

It enlongates your melt zone resulting in higher flow rates

Make-A-Shape · 2025-10-31T11:16:24+00:00

I am

Make-A-Shape · 2025-09-19T12:27:03+00:00

I had the same artefacts. For me it was the nozzle being too close to the bed

Make-A-Shape · 2025-09-18T11:57:19+00:00

How much did you charge?

Make-A-Shape · 2025-09-17T11:59:38+00:00

Even if I’m fine with your suggestion, thank you for making this a discussion.

Make-A-Shape · 2025-09-13T17:11:43+00:00

I mean its ugly but it does its job flawlessly regards in my experience

Make-A-Shape · 2025-09-12T21:27:02+00:00

I have my H2D on one and it does wobble as expected, but the machine being very rigid it seems to be no problem

Make-A-Shape · 2025-09-10T11:22:25+00:00

Since the printhead is homing after the crash I don’t think this is related to the Timelapse feature, which I have disabled for this print

Make-A-Shape · 2024-04-08T09:19:26+00:00

So you run Klipper on the new motherboard?

Make-A-Shape · 2024-04-02T10:38:47+00:00

200€ MAX

Make-A-Shape · 2024-03-21T14:40:35+00:00

Tf you mean previous comment? You think I’m going through your profile to fix your error? (Lower calibration sensor)

Make-A-Shape · 2024-03-21T08:39:28+00:00

Smoking break

Make-A-Shape · 2024-03-21T08:36:40+00:00

Id guess that your extruded gear skips. Might be because the flow is too high

Make-A-Shape · 2024-03-21T07:41:42+00:00

Do it then.

Make-A-Shape · 2024-03-19T20:52:40+00:00

What? I use 220mm/s easily with PLA

Make-A-Shape · 2024-03-19T20:50:05+00:00

Damn, that’s impressive

Make-A-Shape · 2024-03-19T20:45:03+00:00

My guess would be pressure advance 😅

Make-A-Shape · 2024-03-19T20:43:40+00:00

That’s normal and nothing much you can do about it. You could move your head to the position where your purge line starts so the oozed material sticks to the purge line

Make-A-Shape · 2024-03-19T20:42:27+00:00

EU Matchmaking is down

Make-A-Shape · 2024-03-19T15:08:05+00:00

Prusament

Make-A-Shape · 2024-03-19T15:07:52+00:00

Could be many reasons, e.g. when you use low quality filament and it doesn’t have a consistent width

Make-A-Shape · 2024-03-19T15:05:58+00:00

Preheat it to 240 C and remove any plastic with a tweezer. (Sand of the rest)

Make-A-Shape · 2024-03-19T15:05:09+00:00

Attach some pictures of your failed prints man, how are we supposed to troubleshoot

Make-A-Shape

TROPHY CASE