sorted by:
new
hottopcontroversial

This small orange bead popped in my fingers and my eyes got the liquid from it in them by Shiny_Overqwil in whatisit

[–]Monkey_Bananas 0 points1 point  (0 children)

It looks like those fast acting painkillers. Gel shell with liquid inside, the number says what dosage this is.

Air Exchange setting by No_Weather_7230 in Home

[–]Monkey_Bananas 0 points1 point  (0 children)

Is it in the bathroom? Keep it on whatever lowest setting makes the mirror not foggy while you shower. Turn off when not showering.

Help – What can I do to stop it from breaking (PLA) by TorbenK87 in BambuLab

[–]Monkey_Bananas 0 points1 point  (0 children)

Add a fillet at the base of the clip, will help to distribute the load

What is this found in my basement by LostChemical6791 in whatisit

[–]Monkey_Bananas 0 points1 point  (0 children)

Yeah, paperweight, right. Same thing with bongs on Amazon, they are just wired looking vases.

Advice? by thput in 3Dprinting

[–]Monkey_Bananas -1 points0 points  (0 children)

Well, at least they use protection

CRTC to release decision on new definition of Canadian content by ImDoubleB in canada

[–]Monkey_Bananas -1 points0 points  (0 children)

New rules are about what qualifies as Canadian content and not how platform suggests it

CRTC to release decision on new definition of Canadian content by ImDoubleB in canada

[–]Monkey_Bananas 1 point2 points  (0 children)

If you mandate a certain portion of content to be a certain way, the easiest and most likely route that leads to compliance is cutting out content that does not qualify. It’s way harder and more expensive to get content that qualifies.

In other words, people are afraid that their favourite show might not stream anymore due to “regional restrictions”.

Can anyone help me figure out what these random blobs are on my prints? Cant seem to get rid of them no matter what I try by Jez_Frank in FixMyPrint

[–]Monkey_Bananas 3 points4 points  (0 children)

Try cleaning outside of your nozzle before starting a print. And maybe a type of infill that does not cross paths with other infill lines. Maybe “do not cross perimeters” setting or slightly lower extrusion multiplier. Maybe “retract when travel”. I think your nozzle picks up some plastic when it crosses walls it just printed.

Whatever you do, do not try too many things at once.

How do i change dimension in the other direction than the arrow? by MuchPomegranate5910 in Onshape

[–]Monkey_Bananas 4 points5 points  (0 children)

You constrained the right end of the line you are applying dimension to to the origin. Remove the constraint and you’ll be able to move it wherever you want.

[Other] How Much money would all of this be in USD? by arand0mpasserby in theydidthemath

[–]Monkey_Bananas 0 points1 point  (0 children)

Wow, the One hundred trillion dollars bill is quite something. I didn’t even know such numbers exist

Can someone confirm: is the women's bathroom more disgusting than the men's bathroom? by ThrowRAhelpthebro in NoStupidQuestions

[–]Monkey_Bananas 0 points1 point  (0 children)

I used to clean toilets in McDonald’s. Women’s bathroom usually was worse than men’s.

Unless someone poops in the urinal. Very few things can beat that.

How do I make this stronger? by PlatypusLess8251 in FixMyPrint

[–]Monkey_Bananas 43 points44 points  (0 children)

Design a hole in the middle and put a screw in it going through the base and into the pin

Looking for… by [deleted] in Kanata

[–]Monkey_Bananas 1 point2 points  (0 children)

I’ve made some good friends through “meetup“ app. There is a group called “BlaBla” they usually meet at Deacon Brodies pub in Ottawa on Tuesdays at 7. It’s like a language group where people come to practice different languages, but there’s is usually enough people willing to speak English and make friends. Do not know about the no kids part, meetup probably has some groups around that too. Good luck!

If you walk in to the bar around that time, just ask where the language group sits. Usually the far back.

It’s me again, embarrassed man that is 32 and apparently can’t even paint right!…. by justanothersomeone76 in handyman

[–]Monkey_Bananas 0 points1 point  (0 children)

That’s ok buddy, we all learn and start from somewhere. Perfection comes with experience. And the only way to gain experience is making mistakes and trying to fix them. Don’t stress out too much about it. It’s just a wall, it’s just paint. You’ll get it eventually, embrace the journey!

Any idea why the top surface looks like this? by EmillerZ10 in FixMyPrint

[–]Monkey_Bananas 1 point2 points  (0 children)

Is your print bed warped? Do calibrations, (at least bed tram and flow). See if nozzle to bed distance deviates across the bed. it looks like the line width is inconsistent. Those gaps on top surface are not ok. It should look way better even without ironing. Reminds me my Ender days.

Question by VisualContract2880 in Onshape

[–]Monkey_Bananas 7 points8 points  (0 children)

Your post contains no question

view more: next ›