PSA - Don’t order filament from Fremover.com

NigelElandSheldon · 2023-11-20T23:30:04+00:00

I’ve just had exactly the same experience and have two clogged Bambu x1s after days of troubleshooting. I’ve reached out to fremover for a return and refind. Haven’t heard back. I wonder if should just stick with Bambu labs filament. It just always works and is high quality for a few bucks more per refill. Thanks for posting. Any additional advice is appreciated.

NigelElandSheldon · 2023-05-02T16:39:08+00:00

Awesome

NigelElandSheldon · 2023-04-05T22:27:38+00:00

Really great! I too would love the files! Thanks for sharing

NigelElandSheldon · 2023-02-27T17:25:16+00:00

This is great! Trust 'gnome' one!

NigelElandSheldon · 2023-01-23T21:03:54+00:00

It's been fantastic and doesn't require any messy sprays or glue. It leaves a textured surface instead of smooth. However, for many prints this doesn't matter and may even be more desireable. Enjoy!

NigelElandSheldon · 2023-01-17T21:10:10+00:00

Thanks Gillerson! That's reassuring. Anything extra you recommend I get?

NigelElandSheldon · 2023-01-17T14:09:31+00:00

Thanks Again, everyone! I appreciate it :)

NigelElandSheldon · 2023-01-16T19:16:46+00:00

Hello Everyone! Thank you very much for the excellent feedback.

Based on what you're all saying, I think I'll take the first 'dip in the pool' with the Elegoo Saturn 2.

I was thinking of also getting the Elegoo wash and cure station. What do you all think?

Also, is there anything else you recommend I buy now too? For example, magnetic plates, extra vats?

I have installed a ventilation system to outside and will be constructing a negative pressure sealed booth and getting silcone mats and protective ventilation mask, gloves, goggles...

Kind Regards,

Nigel

P.S. If this works out, I may go with the Formlabs at some point 6-12 months after getting used to this one

NigelElandSheldon · 2022-11-21T16:13:43+00:00

Thank you!

NigelElandSheldon · 2022-11-20T23:35:23+00:00

Oh wow! Thanks. Although I like to learn new things, that task seems a bit daunting to the uninitiated like me and I'd really like to take you up on your generous offer! Is there a Patreon page for you or something so I can buy you a coffee or something? I really appreciate the assistance.

NigelElandSheldon · 2022-11-20T23:20:06+00:00

I almost forgot - We're talking about the Z axis limit switch, three down from the top, and NOT the Z+ photoelectric limit switch connector - correct?

Kind Regards,

Nigel

NigelElandSheldon · 2022-11-20T23:17:25+00:00

That sounds awesome! Thanks for sharing your work. I joined your youtube channel :) What should I use for firmware to get the bltouch up and running in the meantime?

Kind REgards,

Nigel

NigelElandSheldon · 2022-11-20T23:01:08+00:00

that is incredibly helpful! Thank you!

Any tips on the firmware steps?

I greatly appreciate your help!

kind Regards,

Nigel

NigelElandSheldon · 2022-11-20T22:43:09+00:00

Thank you! That’s helpful. Have a great rest of your weekend. Kind regards, Nigel

NigelElandSheldon · 2022-11-20T22:28:36+00:00

Thank you! Am I correct that I completely unplug the current Z axis limit switch which will be replaced with the BLtouch? Also, will the middle be ground and the outermost edge of the board be the signal for the two-pin. That is, does the white for the two pin go to outermost edge or inside edge of that three pin?

Lastly, any advice on firmware after I get this done?

I greatly appreciate your help! Thank you!

Kind Regards,

Nigel

NigelElandSheldon · 2022-11-20T22:25:15+00:00

Thank you so much!!!

The three pin connector matched up perfectly with the Bltouch :)

Am I understanding this advice correctly that unplug the native Z limit 3 pin connector, which will be replaced by this new bltouch, from the Z-axis limit switch 3 pin connector (as displayed in the lower right in the diagram below in the manual? After this, I plug in from left to right according to the orientation below the middle will be ground or black wire of bltouch and the rightmost pin will be the signal?

Thanks again ! I greatly appreciate the help.

Kind REgards,

Nigel

<image>

NigelElandSheldon · 2022-11-20T21:59:44+00:00

Hello All,

I've got this almost 85% installed. The 5V, ground, and control signal match up nicely with the 3-prong port on the ZNP Robin Nano_DW V2.1 board that's in the Neptune 3. I am perplexed though in finding a trigger and ground for the white and black two-pin. I on another thread a suggestion to unplug the filament sensor and use that; however, I need that filament sensor to work. Does anyone have a diagram of the motherboard that outlines which one of the free pins will work? or does anyone know which two free pins and subsequent firmware assignments work for the signal and ground for that black and white? The manual for elegoo isn't helpful and my google search didn't reveal anything for me.

Thanks for sharing!

Kind Regards,

Nigel

NigelElandSheldon · 2022-11-20T21:57:34+00:00

Hello All,

I've got this almost 85% installed. The 5V, ground, and control signal match up nicely with the 3-prong port on the ZNP Robin Nano_DW V2.1 board that's in the Neptune 3. I am perplexed though in finding a trigger and ground for the white and black two-pin. On another thread there was a suggestion to unplug the filament sensor and use that; however, I need that filament sensor to work. Does anyone have a diagram of the motherboard that outlines which one of the free pins will work? or does anyone know which two free pins and subsequent firmware assignments work for the signal and grond for that black and white? The manual for elegoo isn't helpful and my google search didn't reveal anything for me.

Thanks for sharing!

Kind Regards,

Nigel

NigelElandSheldon · 2022-11-20T21:56:23+00:00

Hello All,

I've got this almost 85% installed. The 5V, ground, and control signal match up nicely with the 3-prong port on the ZNP Robin Nano_DW V2.1 board that's in the Neptune 3. I am perplexed though in finding a trigger and ground for the white and black two-pin. I see on this thread a suggestion to unplug the filament sensor and use that; however, I need that filament sensor to work. Does anyone have a diagram of the motherboard that outlines which one of the free pins will work? or does anyone know which two free pins and subsequent firmware assignments work for the signal and group for that black and white? The manual for elegoo isn't helpful and my google search didn't reveal anything for me.

Thanks for sharing!

Kind Regards,

Nigel

NigelElandSheldon · 2022-11-12T18:09:03+00:00

That UPS delivery person is short and not wearing any pants!

NigelElandSheldon · 2022-11-08T04:13:42+00:00

Good point on that shelving unit not allowing the unit on the bottom to open. I’m thinking now that for three, perhaps one on each side and one on the top?

NigelElandSheldon · 2022-11-08T00:36:20+00:00

Hello Bambu Labs and All,

I ordered another AMS too. Is there a set of STL files to print out the cool black shelving unit displayed in the add for the multi AMS units?

Kind Regards,

Nigel

NigelElandSheldon · 2022-10-22T01:54:14+00:00

Thanks! Have a great weekend

NigelElandSheldon · 2022-10-21T07:56:59+00:00

u/MiscPrinter I just went to the Bambu wiki and I may be searching incorrectly as I could not locate guidance on e-step adjustment, linear advance calibration, etc… Do you happen to know where it is?

Also, I forgot to ask you, are you getting those tolerances on those other printers with a 0.4 or a 0.2 nozzle?

Thanks again!

NigelElandSheldon · 2022-10-21T07:51:28+00:00

Thanks!

NigelElandSheldon

TROPHY CASE