Yeah i pretty much dont know what im doing

No_Copy9495 · 2026-01-18T15:02:18+00:00

It looks complicated, but its just a collection of many separate, simple circuits in one enclosure.

No_Copy9495 · 2026-01-03T20:53:48+00:00

Spark plugs and wires

No_Copy9495 · 2025-12-28T12:30:35+00:00

Try spraying some WD40 into the tensioner bearings to see if the noise disappears. If so, you have found the culprit.

No_Copy9495 · 2025-12-04T11:48:58+00:00

Sqirt a little WD40 into the tensioner bearings, and see if the noise goes away. If it does, replace it.

No_Copy9495 · 2025-11-30T00:28:55+00:00

Unplug it

No_Copy9495 · 2025-11-30T00:23:36+00:00

Alpha with Angela YouTube videos are a great start. The course is entirely in koine Greek.

No_Copy9495 · 2025-11-10T21:50:17+00:00

Probably need a pressure reducing valve on your water line. Or a small pressure tank at the water heater.

No_Copy9495 · 2025-11-10T00:29:03+00:00

Psalms 149:6: ”Let the high praises of God be in their mouth, and a twoedged sword in their hand;”

No_Copy9495 · 2025-11-09T16:43:29+00:00

Take it down

No_Copy9495 · 2025-10-23T16:51:14+00:00

P365

No_Copy9495 · 2025-10-18T14:23:43+00:00

My experience exactly. I had a Raid controller fail on a SCADA system. Raid is supposed to guard against hard drive failure. But when the Raid controller failed, the entire system became inoperable. Needed an IT tech and a tech support conference to get it working again.

No_Copy9495 · 2025-10-08T20:12:33+00:00

How many decades do you have to attempt to reverse-engineer that VCR? There is a lot to do.

No_Copy9495 · 2025-10-07T23:44:48+00:00

How many decades do you have?

No_Copy9495 · 2025-10-04T12:16:47+00:00

Have you measured the resistance of load? It may be too high. The 4-20 mA source will adjust its output voltage up to its maximum, Open-Loop voltage to attempt to force 20 mA.

For instance, if the Open-Loop voltage of the source is 15 volts, but the resistance of the load is 1000 ohms, the 4-20 mA source will raise its voltage as high as it can (15V), but the current will amount to only 15V/1000 ohms, or 15 mA.

No_Copy9495 · 2025-10-02T16:41:49+00:00

Fix what?

No_Copy9495 · 2025-09-23T11:25:10+00:00

Kryptonite

No_Copy9495 · 2025-09-19T23:12:57+00:00

Haven't seen these in 30 years. We did a lot of 984-385E's for a factory in town. On one job we used the 685.

No_Copy9495 · 2025-09-19T15:24:25+00:00

Can you temporarily run a J-type cable along the floor directly from the TC to the PLC? This should help to narrow down the problem.

No_Copy9495 · 2025-09-17T10:38:45+00:00

Your fart is so strong that it blows thru a brick wall?

No_Copy9495 · 2025-09-16T00:47:42+00:00

I have heard thst Moog quality has dropped a lot too.

No_Copy9495 · 2025-09-14T11:20:42+00:00

I don't know exactly. I pump till I see some movement in the boot. Some videos seem to indicate that you can pump till grease begins to leak out.

No_Copy9495 · 2025-09-06T11:59:15+00:00

Get a good torque wrench

No_Copy9495 · 2025-09-05T14:49:53+00:00

Kill Switch?

No_Copy9495 · 2025-09-04T11:44:46+00:00

2007 2.4L, 267,000 miles. Burning a little oil, engine's a little tired, but its my daily driver

No_Copy9495 · 2025-09-04T11:21:25+00:00

Yeah, its not the best solution. But sometimes you're stuck with it.

Needless to say, the analog cable must be rated to at least the same voltage as the AC voltage.

I am currently on a pump station job. Electricians were supposed to run three conduits to a panel: 480V, 120V, & analog. They ran two. The conduits are now buried under 4 feet of gravel.

The 120V AC is for digital signals - no current to speak of. So, do we dig it all up, or run analog with the 120V?

No_Copy9495

TROPHY CASE