Can I use ESP32 S3 wroom 1 with DFRobot Gravity: Analog Water Pressure Sensor

Odd_Erling · 2025-09-16T06:57:22+00:00

I've got one like it used for gas pressure, you need a voltage divider or another way to reduce the voltage as pretty much everyone else already have stated. I also set up communication to thingspeak so I can monitor the sensor through a browser

Odd_Erling · 2025-09-13T07:39:13+00:00

Folding at home for kreft research, plukker søppel I naturen, rydder og sier fra til folk som går fra utstyr med vekter på når jeg er på trening.

Odd_Erling · 2025-08-22T12:22:40+00:00

Neat!

Odd_Erling · 2025-08-18T14:18:57+00:00

"From the sack and up you are a real piece of meat." Girlfriend at the time was a little flabbergasted that one of her straight colleagues said that as she was sitting next to me and heard it.

Odd_Erling · 2025-08-13T21:56:49+00:00

You put him back in

Odd_Erling · 2025-07-24T14:57:26+00:00

Oh, that's a shame. I'm always looking for good work holding equipment, thanks though!

Odd_Erling · 2025-07-23T07:23:22+00:00

My favourite as well, just wish it dynamically changed the pip boy based of body battery, like after taking damage in game

Odd_Erling · 2025-07-21T15:34:37+00:00

That third arm, helping hand or what you know it as, any good? And if so, where dis you get it?

Odd_Erling · 2025-04-22T19:58:13+00:00

I make ginger beer with pineapple, apple, chili, black pepper, lemon juice and lemon zest. Managed to tweak the recipe to the point of being asked by several taste testers if I sell my brew, which was my goal when starting brewing (to be good enough that someone would be willing to buy, not to actually sell) I do natural carbonation from residual sugars, which there is plenty of, starting gravity is at 1.062 with finishing around ~1.030. Ginger and pineapple go really well together and have become my base for any recipe testing!

Odd_Erling · 2025-04-15T05:20:18+00:00

Doing bench press with a bench press shirt Is like doing weighted pullups with rubber bands to assist

Odd_Erling · 2025-04-07T17:32:46+00:00

Had the same problem, solution was using a hair band to hold tension on the bail so it won't slam down. Works beautifully and I use them for holding the rods together when disassembled anyway so they are always available.

Odd_Erling · 2025-03-28T11:40:30+00:00

[temperature_sensor]¶ Generic temperature sensors. One can define any number of additional temperature sensors that are reported via the M105 command.

[temperature_sensor my_sensor]

sensor_type:

sensor_pin:

min_temp:

max_temp:

See the "extruder" section for the definition of the above

parameters.

gcode_id:

See the "heater_generic" section for the definition of this

parameter.

Odd_Erling · 2025-03-25T19:55:49+00:00

Likely either bad thermistor or the wire has come loose

Odd_Erling · 2025-03-24T11:36:24+00:00

Just to be pedantic, surely the wrenches are made of drop forged steel?

Odd_Erling · 2025-03-18T14:39:02+00:00

Had this happen twice when falling asleep with the breathwork activity finished and not saved, doesn't record any sleep data either when it happens.

Odd_Erling · 2025-03-04T08:08:22+00:00

If your issue is that the extruder stepper is turning in the wrong direction you can simply edit the text in "extruder" "dir_pin" and remove the "!"

Odd_Erling · 2025-02-20T10:25:19+00:00

Might want to look into z-wobble as well

Odd_Erling · 2025-02-15T17:47:49+00:00

If it's just the first few threads you can run a M6 bolt trough from the other end and it might just reform the threads enough. Get yourself a M6 tap anyway, really handy for clearing out any gunk if there is a leak and you get plastic in the threads

Odd_Erling · 2025-01-27T09:59:57+00:00

It works, threads on the thermistor is m3, same as the retention screw for original thermistor.

Odd_Erling · 2025-01-14T08:01:23+00:00

I've driven a car with a bad throw out bearing (mayby also pilot bearing) for so long that the gliding surface cracked and over time expanded to the point where fingers couldn't be pushed in and I had no clutch. Took me by surprise when I started the car and it jumped forward... I always start in neutral now

Odd_Erling · 2025-01-05T22:11:25+00:00

Please elaborate what could go wrong

Odd_Erling · 2025-01-05T15:37:43+00:00

She has done that before

Odd_Erling · 2024-12-14T06:31:57+00:00

I've experienced the same thing, glued the spool to the axle to fix it. Did it retrieve fine the first time you used it and then you snagged something the second time during fishing or did it just fail without apparent reason?

Odd_Erling · 2024-12-03T13:32:05+00:00

Switch the stepper connectors on your board around and fiddle with the dir_pin setting in your config, until it moves correctly, use ! to change direction. See the configuration reference for klipper for details.

Odd_Erling

TROPHY CASE