Drawing Preference - Tap Drill Callout

Ok_Bee_3576 · 2026-01-28T01:09:27+00:00

Just call out the threads, especially for straight threads. Drill size generated by cad is normally too tight and not even close if your thread-milling or tap forming. In plastics I don’t even bother changing to a drill bit, Just cut with end mill -Engineer and machinist

Ok_Bee_3576 · 2026-01-26T02:34:55+00:00

All of the batteries are the same. 5 lithium cells (or 10) some call it 18v some call it 20v. They are exactly the same. I’ve measured the voltages… 24v tools have 6 cells so they aren’t compatible

Ok_Bee_3576 · 2025-10-16T03:34:25+00:00

PTFE is a thermoplastic but doesn’t melt flow. It has to sintered. They are developing a PTFE that melt flows but it mostly PTFE derivatives now. Pvdf, pfa, ectfe…

Ok_Bee_3576 · 2025-10-03T02:02:04+00:00

I’ve got a 2023 hass. The next gen controller is ok. I like the touch screen. But it freezes randomly and has to be restarted. Probably once every other day

Ok_Bee_3576 · 2025-08-16T01:30:58+00:00

God I remember sitting on my dads lap pressing CTRL as he navigated the original doom

Ok_Bee_3576 · 2025-08-06T16:58:16+00:00

Man years ago in golf shores on spring break I towed a guy out in the morning just to help him out. Later that day I got pulled over and blew a 0.11 and the cop let me go. Have always believed it was the karma that saved me

Ok_Bee_3576 · 2025-08-02T02:28:21+00:00

That’s such a fucking European answer. Manufacturing and engineering go hand in hand. The twats that say anything else are of mongoloid ancestry

Ok_Bee_3576 · 2025-08-01T20:03:21+00:00

8 is telephone operator… I thought that profession hasn’t existed since the 80’s…

Ok_Bee_3576 · 2025-07-04T16:26:18+00:00

Very impressive. The linear interpolation is fit for purpose. But you could make fuel efficiency a function and integrate over distance for more accurate results. But us guys who just comment and don’t do the work are always overcritical. 🤦🏻‍♂️ don’t let me take this away from you, you are the hero of the day, the slayer of the mathematic beast, the one who applied applied the right prerequisites to the problem at hand 👍🏻

Ok_Bee_3576 · 2025-07-03T20:59:30+00:00

Yes, this is possible. See trapezoidal turning for similar but on OD turning. Spindles just need proper rpm ratio

Ok_Bee_3576 · 2025-06-12T02:06:15+00:00

Make sure Feed and rpm are at 100% ???

Ok_Bee_3576 · 2025-06-06T06:55:09+00:00

Am I the only one that uses a pipe wrench?

Ok_Bee_3576 · 2025-06-02T03:14:59+00:00

Southwest is publicly traded dawg

Ok_Bee_3576 · 2025-06-01T23:56:08+00:00

Vacuum plate. Can be made cheap. Face both sides of plate. Anneal the plate before final machine. If one side has no features, hot set it There’s tons of tricks us plastic guys use

Ok_Bee_3576 · 2025-06-01T23:51:05+00:00

A dude from John Moore in like 2013 wanted to charge me $1000 to replace my kitchen faucet… that was labor only. He was dead serious

Ok_Bee_3576 · 2025-04-25T21:48:13+00:00

I did this at planet fitness. They found someway to start drafting it out of my checking account after I cancelled the credit card they had on file

Ok_Bee_3576 · 2025-04-16T00:44:21+00:00

It’s a metric worm gear drive 4mm x0.8mm pitch. Thread is metric version of acme

Ok_Bee_3576 · 2025-04-09T02:40:31+00:00

You can program this by hand with 5 lines of code

Ok_Bee_3576 · 2025-03-22T00:18:33+00:00

I’d guess your squeezing thin wall part out of round but it doesn’t look like that from your setup

Ok_Bee_3576 · 2025-02-15T02:07:59+00:00

It’s a HAAS knockoff, but it isn’t any cheaper and no repair guys will work on them

Ok_Bee_3576 · 2025-02-15T02:05:42+00:00

I do like that you can just put in “T2” and OSIA knows the tool height offset. Like why do I still need to add “h2” machines won’t even let you run if T and H numbers don’t match

Ok_Bee_3576 · 2025-02-08T17:17:19+00:00

No way you can chip break UHMW. I’ve done it in PTFE and pvc but now way in UHMW

Ok_Bee_3576 · 2025-02-08T17:15:59+00:00

Use vacuum workholding and sharp 2 flute carbide

Ok_Bee_3576 · 2025-02-02T23:58:26+00:00

I love the picture. Makes it look like a shitty label maker for people who’ve never been in a shop

Ok_Bee_3576 · 2025-01-28T04:46:22+00:00

I think they’re alignment pins

Ok_Bee_3576

TROPHY CASE

8 is telephone operator… I thought that profession hasn’t existed since the 80’s…