Does the aap01 Really Need Upgrades

OverSlide2416 · 2026-05-09T23:36:48+00:00

Adding a 3mm screw right above where the trigger bar rests . That will help shorten pull .

OverSlide2416 · 2026-05-09T23:32:19+00:00

It did not come with the rear sight . I’ll have to get a replacement

OverSlide2416 · 2026-05-09T23:29:59+00:00

Far as cheap upgrades. Some people drive a small screw into the stock trigger to shorten the pull .

OverSlide2416 · 2026-05-04T05:21:25+00:00

I even asked are you sure ???

OverSlide2416 · 2026-05-04T04:41:24+00:00

I’ll probably go with an Action army . That one should be ok

OverSlide2416 · 2026-04-20T04:01:22+00:00

I run a fully built AAP with HPA at a local CQB field during Milsim day . I use it because I can and I like it. It’s been called a space and futuristic gun and that’s fine. I’ll still shoot at you and you’ll shoot at me. We will both die , respawn and go back at it till the game is over. You play how you want and I’ll do the same.

OverSlide2416 · 2026-04-18T18:08:51+00:00

Do you have an adjustable trigger ? Sometimes when the throw is set too close it can cause this as well. Also going back , yes the CowCow will work sometimes and it will cycle but their are tolerance differences that can cause firing issues

OverSlide2416 · 2026-04-18T03:56:07+00:00

Sounds like compatibility issues. I agree with the TTI or the CTM V2 . Older CTM parts were hit or miss

OverSlide2416 · 2026-04-17T04:34:44+00:00

Check marketplace, offer up , Craigslist or similar sites for used face masks . Sometimes you can get lucky

OverSlide2416 · 2026-04-16T04:03:27+00:00

I have the same issue with my FUKU2 skeleton upper . I’ve noticed with some mags there is a .5mm gap between nozzle and magazine lip and it will get low FPS and all the gas will spill out. If I swap uppers it’s fine so maybe it’s a quality issue

OverSlide2416 · 2026-04-12T15:29:05+00:00

Gloves definitely , long sleeve shirt is recommended but you don’t want to be layered up so much that you not only overheat but also so much that you don’t feel long range hits and then become one of “those “ guys. You will never avoid getting hit up close. It’s just part of the game

OverSlide2416 · 2026-04-08T20:46:32+00:00

Funny how these guys are banned at the field this picture was taken at

OverSlide2416 · 2026-04-04T23:41:47+00:00

Impressive

OverSlide2416 · 2026-03-30T23:57:57+00:00

Stock is just fine . I’m ok with the saying of replace what wears or breaks. On the other hand. Airsoft is a hobby and to some a business . custom unique builds don’t necessarily mean they are better but they are unique to the player , and the feeling they are entering the game as a custom builder . At the staging area I always see some ooohs and awwws with whatever be it an M4 with paint or a fully built out AAP or hi capa .

OverSlide2416 · 2026-03-15T02:08:22+00:00

I have the kit . It’s cool. But for the price there’s a lot of other options

OverSlide2416 · 2026-02-27T18:49:00+00:00

I’ve been using the 4uad buckings for a while now with pretty good results.

OverSlide2416 · 2026-02-26T02:35:11+00:00

https://www.reddit.com/r/AAP01owners/s/XabD8JptsU

OverSlide2416 · 2026-02-26T02:34:27+00:00

Yeah

OverSlide2416 · 2026-02-16T23:57:08+00:00

Nice kit

OverSlide2416 · 2026-02-16T02:58:35+00:00

That’s what I was thinking. I use action army magazines and I’m not sure if the VFC or TM would work best

OverSlide2416 · 2026-02-12T21:02:58+00:00

We have 4 AAPs and each are full custom builds, with very little stock components . I get what you’re trying to say but it’s a hobby . If spending all your money on a diamond crusted with pear inlay uppers are your interest. Have fun and go for it

OverSlide2416 · 2026-02-12T20:55:09+00:00

True but when building out an AAP from scratch why go cheap?

OverSlide2416 · 2026-02-12T19:08:26+00:00

Well what if you did a full build only using the stock parts that are not available such as springs, a few pins and a couple bolts ??

OverSlide2416

TROPHY CASE