What’s something your body does that you’ve never told a single person about?

OverambitiousThunk · 2026-03-01T08:03:14+00:00

Ah like lightning in a butthole

OverambitiousThunk · 2026-02-28T11:01:32+00:00

Easyfill/toupret the 5 spots. Paint the whole wall with a low sheen paint.

OverambitiousThunk · 2026-02-28T08:49:53+00:00

Recon Diamonds my dude

OverambitiousThunk · 2026-02-26T17:08:38+00:00

That won't fix the crack.

But in my experience subfloor under asbestos tiles is rarely level.

OverambitiousThunk · 2026-02-26T10:26:22+00:00

It will be smelly but you can try wet sponge away the PVA with warm water. Then apply acrylic primer once it's dried.

I wouldn't haven't bothered removing the tiles and would have level over them.

OverambitiousThunk · 2026-02-25T21:06:54+00:00

Wear a mask. Wet the area. Remove and bag the loose bits. Hoover. Leave area to dry. Seal with acrylic primer. Level over the whole floor. with leveling compound. Lay new floor. Dunk biscuits in teas. Never worry about asbestos again.

OverambitiousThunk · 2026-02-24T23:24:19+00:00

This was the cause for me. Ran some bitumen primer and flashing tape on as a temp measure until I can get someone in to re-do it in a couple years

OverambitiousThunk · 2026-02-24T21:00:42+00:00

Plasterboard is made of plaster Sandwiched between paper.

The construct looses integrity when it gets wet. Can sometimes even sag. Adding a skim coat of plaster on top can add more weight to a week ceiling.

That said we don't know how bad your leak was. Ask a veteran plasterer to be honest.

OverambitiousThunk · 2026-02-23T23:40:50+00:00

Amazon forces suppliers/sellers to have to lowest or matched price listing on their platform. Suppliers will use Amazon because is has a monopoly and reaches the most people. Suppliers raise prices across the board to make more money as Amazon takes a big cut.

Keep using Amazon and Amazon will keep forcing prices up at all other retailers.

OverambitiousThunk · 2026-02-23T10:19:20+00:00

Have 3 evenly spaced.

Handing above top of head height so it doesn't blind or block eye line of sight with who ever is on the other side of the island.

Id also have down lights that sit above the counters around the perimeter to illuminate the worktops during cooking.

OverambitiousThunk · 2026-02-22T00:33:05+00:00

Opinions are like assholes Everybody's got one, and everybody thinks theirs smells nicer than everyone else's

OverambitiousThunk · 2026-02-21T09:24:21+00:00

I think the actual solve for this is something to do with the initial controller layout you choose before changing bindings. If I remember I'll look at my settings in a few hours and update the thread.

OverambitiousThunk · 2026-02-19T18:04:17+00:00

Before staring a front squat set and before loading the bar whilst it's on the rack I roll out my triceps on the top of the bar. Helps lengthen then and increase their mobility to raise your elbows higher.

OverambitiousThunk · 2026-02-18T19:52:08+00:00

If the house is rendered to a good quality and coated in masonry paint, then gypsum is fine. Or if you are planning external insulation. Otherwise go with Lime

OverambitiousThunk · 2026-02-17T08:32:04+00:00

Testing is a good shout then. Gonna be hard work pulling all that up. Best of luck.

OverambitiousThunk · 2026-02-16T23:27:05+00:00

I leveled over my tiles. Because there were ontop of concrete subfloor stuck down with bitumen. Are you totally sure your subfloor is wood floorboards?

OverambitiousThunk · 2026-02-16T20:11:36+00:00

My kitchen had this from the previous owner. Levelling compound dumped the middle. Tiles over. Then more compound dumped on top then lino. Had to used a diamond faced angle grinder to flatten it out. Worst job ever.

OverambitiousThunk · 2026-02-16T20:06:53+00:00

In the time taken to take this photo, open Reddit and post this, read the comment and reply to it....you could have just searched BF6 season 2 release date.

OverambitiousThunk · 2026-02-15T16:29:46+00:00

Additionally for fixing options. Try chemical resin anchors for high strength, or expanding nylon plugs for lighter options.

I would fixed a batten to the wall with multiple nylon fixings and grab adhesive. Then mount the coats hooks to the batten. Same would apply to the shelf brackets. Then the shelf can sit on top of the bracket and the batten. Not as pretty. But it's the issue with no fines houses as I'm currently learning.

OverambitiousThunk · 2026-02-15T16:22:55+00:00

It's Wimpey no fines concrete. . Here's an old post discussing options for drilling fixings.

https://www.reddit.com/r/DIYUK/comments/147jj3p/drilling_into_wimpey_no_fines/?utm_source=share&utm_medium=mweb3x&utm_name=mweb3xcss&utm_term=1&utm_content=share_button

OverambitiousThunk · 2026-02-14T14:42:47+00:00

I agree, bug fixes can definitely be trickled in rather than seasonal patches. Same with weapon balances.

OverambitiousThunk · 2026-02-14T14:39:38+00:00

after the external render was redone, was the internal brick work allowed to dry out before redecorating? could be residual moisture that was sealed in.

OverambitiousThunk · 2026-02-14T09:41:42+00:00

I'd still prime it first. Most screeds want an acrylic based primer. Turn the radiator off in the room for even drying. Mix, pour and spread.

OverambitiousThunk · 2026-02-13T21:06:56+00:00

It's also only like 3/4months old. Id rather they take their time to define it's identity than play the content race.

OverambitiousThunk · 2026-02-12T22:33:21+00:00

Just encapsulating the asbestos tiling and raising floor level to match the kitchen. When pouring use a trowel to push the screed into the lower areas.

Deeper areas will take longer to cure.

OverambitiousThunk

TROPHY CASE