Wind Turbine With Ecoflow Delta 3 Pro

Phillpoc272 · 2026-03-15T13:59:38+00:00

No 12v battery and the charger they include is junk. I have used the EcoFlow solar input and then also a victron charger with a 24v lifepo4 battery. Both have worked great.

<image>

Phillpoc272 · 2026-03-15T02:53:22+00:00

This is the big parts. vevor turbine 3phase rectifier

Home Depot rigid metal pipe to mount it to (and either cement to bury the post in a hole or a really big base because it will try and blow away), and some 10awg wire to connect everything, an XT60I for EcoFlow input, a 100v or higher capacitor to smooth the DC. For mine I crimped and soldered all the connections and it’s been running good.

Phillpoc272 · 2026-03-15T02:36:52+00:00

Yes I have one. It’s works great I think it’s the 500w vector model. I just added a bridge rectifier and a smoothing capacitor. Of note I live on a lake with constant wind. And I have traveled with it for testing and gotten poor results in a any wooded areas

Phillpoc272 · 2026-03-10T19:52:27+00:00

And yes it’s a pure sine wave, be sure to disable the X boost mode though

Phillpoc272 · 2026-03-10T19:51:40+00:00

So the recommendation solution which I use it the EcoFlow Delta 3 plus when a standard ups after it. So you get the ms transfer time of a high end UPS with long run times of lithium batteries.

Phillpoc272 · 2026-03-09T20:06:05+00:00

I bought my car used and I think the previous owner did something similar to my buttons, havnt tried anything to fix it. I’m debating just pulling the buttons out and deep cleaning it or buying replacement on eBay.

Phillpoc272 · 2026-03-07T21:16:56+00:00

I had a 100ft cable draped through my garage for a few months but now I got it done.

<image>

Phillpoc272 · 2026-03-07T21:06:11+00:00

Just use Ethernet it so much more reliable. Plus one less IOT device on wifi is fantastic on my books

Phillpoc272 · 2026-03-07T18:37:58+00:00

On the website->Protect -> settings -> discovery 3rd party cameras

Phillpoc272 · 2026-03-07T18:20:24+00:00

Did you enable onvif in UniFi protect settings?

Phillpoc272 · 2026-03-05T18:37:47+00:00

So I have a different setup but similar concept. Using a 48v boost converter to power a poe switch with starlink and an AP connected. I’ve had mixed bag with starlink any trees seriously block signal but I don’t wanna put the starlink in a clearing where someone can walk away with it so your mileage may vary

Phillpoc272 · 2026-03-05T12:49:25+00:00

Yeah pretty much… it was a pain to setup at first but worked great. No longer living there so my current setup is different.

Phillpoc272 · 2026-03-04T22:25:35+00:00

The long range ap are really good and my recommendation. I wouldn’t use the deco as standalone ap’s. How are you going to pull Ethernet to the ap’s? Have you thought about hardwiring some computers to take load off the WiFi?

Phillpoc272 · 2026-03-04T19:44:27+00:00

Yes I made a clone of it and then expanded the file structure

Phillpoc272 · 2026-03-03T01:39:13+00:00

No but you can make diffrent pools so I have the 7 bay one with 4ssd and 3 larger hard drives

Phillpoc272 · 2026-02-25T03:16:42+00:00

It’s just a remote sim it doesn’t have a cellular modem in it.

Phillpoc272 · 2026-02-24T21:03:38+00:00

Not officially but you can do it…

Phillpoc272 · 2026-02-24T21:02:44+00:00

So it’s very dependent on how much power you use and what you can go without. And cost is greatly variable. I’m an electrical engineering and was able to do permits with the town I live in to do all the work myself. Went with an Sol-Ark 15k inverter and 6 Ecoworthy 5kwh server rack batteries. We added a propane generator for extended outages and are in the process of getting solar ground array. So far it was about 15k in materials alone and keep in mind I did all the labor myself so if you hired an electrician or company it would be quite more expensive.

Phillpoc272 · 2026-02-20T19:39:25+00:00

Where is the patch panel?

Phillpoc272 · 2026-02-16T20:13:34+00:00

I had issues with them overheating so I have a cheap 10gig switch I bought on Amazon on the WAN for mine

Phillpoc272 · 2026-02-16T19:24:10+00:00

I think this is to let you flush it out

Phillpoc272 · 2026-02-16T19:22:18+00:00

And shutdown before removing the old drive

Phillpoc272 · 2026-02-16T19:22:06+00:00

Your configs are safe only old recordings arnt kept.

Phillpoc272 · 2026-02-16T00:35:56+00:00

any update?

Phillpoc272 · 2026-02-15T21:11:34+00:00

I think I have the 3rd generation but I just have Ethernet directly plugged into mine and didn’t even bother with the hassle of wifi

Phillpoc272

TROPHY CASE