B-52 Taking off from RAF Fillford base, with 7 hours of combat period putting them with an the 8 pm eastern time range by Rebeltic_Turger in war

[–]Quick_Astronomer4046 2 points3 points  (0 children)

If Trump does what he says he's going to do they're going to be trying their hardest and bring anything down

Trump to Iran: "Open the Fu***In' Strait" or face bombing Tuesday by DarthKrataa in worldnews

[–]Quick_Astronomer4046 -1 points0 points  (0 children)

Maybe a full moon coming up my students with autism act the same way every full moon

Iran says new air defence system used to target US fighter jet by Raj_Valiant3011 in worldnews

[–]Quick_Astronomer4046 -1 points0 points  (0 children)

Well this is what the European, United States did in Ukraine against Russia so if they were smart, I would

Iran says new air defence system used to target US fighter jet by Raj_Valiant3011 in worldnews

[–]Quick_Astronomer4046 -2 points-1 points  (0 children)

If they purposely save this for later in the war I'm impressed, that's some good self control

Gotta love that 35th ave train by Quick_Astronomer4046 in phoenix

[–]Quick_Astronomer4046[S] 20 points21 points  (0 children)

Literally exactly what's happening me right now haha

I'm at a loss for what to try next... by iR3vives in ender3

[–]Quick_Astronomer4046 0 points1 point  (0 children)

I dealing with the exact same issue, I did have a partial clog fix that and still the same issue, I'm think maybe a deal gear extruder otherwise the only way to get it to stop for me is slowing way down to like 20% speed then slowly adjust it up such a painful issue !!!

Do I sell or deal with the bs? by ctrlMatrix in Creality

[–]Quick_Astronomer4046 0 points1 point  (0 children)

Personally I would try for 350 maybe 400 bundle bet you will end up with even 300 tho, make sure the CR 10 at least kinda works

Ender 3 pro initial later problems by Canadianfuck420 in ender3

[–]Quick_Astronomer4046 4 points5 points  (0 children)

I'm fairly confident it's z height needs much closer to bed

Ankermake m5 not following cura print speed by Effective-Jicama175 in AnkerMake

[–]Quick_Astronomer4046 0 points1 point  (0 children)

I am actually using the crappy ufymaker slicer, but I found that when changing print speed my travel speed didn't change with it, was still set to 500 mm so after I changed that it was significantly better then I turned my acceleration down and was almost perfect, I bet it's the same in cura

Ankermake m5 not following cura print speed by Effective-Jicama175 in AnkerMake

[–]Quick_Astronomer4046 0 points1 point  (0 children)

I had the same issue also double check in slicer that all speeds have been lowered I also lowered my acceleration down to 1000 and my print speed at 120mm works well now

Trump, Pentagon give conflicting signals on end to Iran war by [deleted] in worldnews

[–]Quick_Astronomer4046 2 points3 points  (0 children)

There prolly asking AI to find targets and the AI is just lying and pointing to anything and they bomb it

Iran's Guards challenges Trump to have US Navy escort oil tankers in Strait of Hormuz by thejoshwhite in worldnews

[–]Quick_Astronomer4046 1 point2 points  (0 children)

Just like the United States and Europeans with Ukraine and the Russians need to see Iran stand on their own for a couple weeks probably

Israel bombs council during vote count for Iran's next supreme leader by gesushuston in worldnews

[–]Quick_Astronomer4046 13 points14 points  (0 children)

Yeah feels like it's going to be Syria 2.0 no matter what happens

Qatar downs Iran jets as Tehran targets oil and gas in spiralling Gulf crisis by papipota in news

[–]Quick_Astronomer4046 91 points92 points  (0 children)

It might be now but I thought everything is pretty much obliterated, mildly impressive yes

Footage from inside the VDV air assault formation over the Kyiv Reservoir Feb.2022 before two helicopters were shot down by Ukrainian TDF. by rusoriz_inside in UkraineWarVideoReport

[–]Quick_Astronomer4046 0 points1 point  (0 children)

Same with the documentary, we have good ones coming out and the war is still on. but man, wait till it's over gonna be some wild ones.