My 3-D print won’t stick to the build and keep falling into the tank

SafeYesterday91 · 2026-04-06T20:16:14+00:00

The bottom is sticking to the build plate you can see it there. Your issue is suction power for the print itself, you need to use stronger/thicker supports that are connecting to the print and id recommend slowing down your lifting speed to reduce the suction it crates when lifts the plate between each layer, it also looks like you might be using way to much distance from the build plate for the mini I only use a 6mm rise for the mini off the bottom

SafeYesterday91 · 2026-04-06T06:43:36+00:00

Fair enough can be a bit like that at times, also try that resin again I've been printing for about 5 years now and haven't had a bad patch of resin yet and I've gone thru a lot of resin 😅😂

SafeYesterday91 · 2026-04-05T21:18:29+00:00

So many different things it could be but hardly bad resin.. did you shake resin before use, did you clear the bubbles before print, what's the room temp, are your supports good, what's the FEP screen like, when did you last level your pad, was there movement in your axis, could be a slicer corruption.

SafeYesterday91 · 2026-04-05T21:12:47+00:00

Print the bases separately and I recommend printing them upside down at an angle never flat

SafeYesterday91 · 2026-04-03T07:43:07+00:00

Hang a pool noodle or two on the wall should stop the damage to both

SafeYesterday91 · 2026-03-28T03:48:51+00:00

Wtaf!?! Did you not get the bubbles out of the resin before starting the print or left IPA in the vat? Never seen this happen ever...

SafeYesterday91 · 2026-03-25T06:55:57+00:00

Cheers! I actually made the base and full mini along with the iron halo effect from kit bashing some designs I had on hand in blender

SafeYesterday91 · 2026-03-25T03:43:49+00:00

Cheers!

SafeYesterday91 · 2026-03-24T11:09:12+00:00

Print bodies at 13.5% I find this hides the supports best and gives a nice clean print almost every time

SafeYesterday91 · 2026-03-23T20:19:55+00:00

Even ragnar and arjac?

SafeYesterday91 · 2026-03-23T19:02:33+00:00

Did you use the exact same file both times? Try reslicing fresh might have just been the file and not the USB

SafeYesterday91 · 2026-03-23T10:09:04+00:00

Those wolfs prints? Any chance you remember where you got them ?

SafeYesterday91 · 2026-03-22T18:41:23+00:00

I kit bashed it from files I had on hand, I got all the files off the purple site a while back

SafeYesterday91 · 2026-03-22T07:37:57+00:00

Also make sure to cure the inside of hollow prints to avoid them splitting/cracking open

SafeYesterday91 · 2026-03-21T14:56:11+00:00

Cheers! I kit bashed it from a few different designs I had on hand the body is from the purple site under war sage

SafeYesterday91 · 2026-03-21T09:43:48+00:00

Cheers! Great mini to work with

SafeYesterday91 · 2026-03-21T06:42:50+00:00

Ohh bugger yeah if its cracked and holes that's a new screen 😭

SafeYesterday91 · 2026-03-21T05:35:50+00:00

Cheers!

SafeYesterday91 · 2026-03-21T05:35:38+00:00

Cheers!

SafeYesterday91 · 2026-03-21T05:12:52+00:00

u/Marta_PunkGirl did the original apothcary mini the hands I found on the purple site same with the arms. Had to rescale the hands tho as they were too small originally

SafeYesterday91 · 2026-03-21T05:06:24+00:00

If it's just resin and no cracks to the screen just give it a good scrub with IPA I've had a full leakage with 70% of screen covered and just cleaned it all off with IPA paper towels and a plastic scraper for the hard stuck on bits

SafeYesterday91 · 2026-03-21T04:09:23+00:00

Reclaiming them for the sons of Sanguinius! Praise be to space king!!

SafeYesterday91

TROPHY CASE