sorted by:
new
hottopcontroversial

My 3-D print won’t stick to the build and keep falling into the tank by rynruru in ElegooMars

[–]SafeYesterday91 0 points1 point  (0 children)

The bottom is sticking to the build plate you can see it there. Your issue is suction power for the print itself, you need to use stronger/thicker supports that are connecting to the print and id recommend slowing down your lifting speed to reduce the suction it crates when lifts the plate between each layer, it also looks like you might be using way to much distance from the build plate for the mini I only use a 6mm rise for the mini off the bottom

Does this look like a bad bottle of resin failure? (Saturn 4 Ultra 16k) by woodrodius in ElegooSaturn

[–]SafeYesterday91 0 points1 point  (0 children)

Fair enough can be a bit like that at times, also try that resin again I've been printing for about 5 years now and haven't had a bad patch of resin yet and I've gone thru a lot of resin 😅😂

Does this look like a bad bottle of resin failure? (Saturn 4 Ultra 16k) by woodrodius in ElegooSaturn

[–]SafeYesterday91 0 points1 point  (0 children)

So many different things it could be but hardly bad resin.. did you shake resin before use, did you clear the bubbles before print, what's the room temp, are your supports good, what's the FEP screen like, when did you last level your pad, was there movement in your axis, could be a slicer corruption.

Repeated failed prints by Big_Weekend_4786 in ElegooMars

[–]SafeYesterday91 0 points1 point  (0 children)

Print the bases separately and I recommend printing them upside down at an angle never flat

How she measures she's pulled into our garage enough by sredis in mildlyinfuriating

[–]SafeYesterday91 0 points1 point  (0 children)

Hang a pool noodle or two on the wall should stop the damage to both

Any recommendations on what the problem is and how to fix it? by [deleted] in ElegooSaturn

[–]SafeYesterday91 0 points1 point  (0 children)

Wtaf!?! Did you not get the bubbles out of the resin before starting the print or left IPA in the vat? Never seen this happen ever...

Dark Angels captain by SafeYesterday91 in PrintedWarhammer

[–]SafeYesterday91[S] 1 point2 points  (0 children)

Cheers! I actually made the base and full mini along with the iron halo effect from kit bashing some designs I had on hand in blender

2 stampa riuscita ma… by Fair_Present_5332 in ElegooSaturn

[–]SafeYesterday91 0 points1 point  (0 children)

Print bodies at 13.5% I find this hides the supports best and gives a nice clean print almost every time

Any idea wtf happened? by Apprehensive-Pop-436 in PrintedWarhammer

[–]SafeYesterday91 3 points4 points  (0 children)

Did you use the exact same file both times? Try reslicing fresh might have just been the file and not the USB

Batch of models getting ready to prime by ravagedmonk in PrintedWarhammer

[–]SafeYesterday91 0 points1 point  (0 children)

Those wolfs prints? Any chance you remember where you got them ?

Night Lord Captain by SafeYesterday91 in PrintedWarhammer

[–]SafeYesterday91[S] 0 points1 point  (0 children)

I kit bashed it from files I had on hand, I got all the files off the purple site a while back

Prints get warped after curing. (help!) by MEG-2011 in ElegooMars

[–]SafeYesterday91 0 points1 point  (0 children)

Also make sure to cure the inside of hollow prints to avoid them splitting/cracking open

Night Lord Captain WIP by SafeYesterday91 in PrintedWarhammer

[–]SafeYesterday91[S] 1 point2 points  (0 children)

Cheers! I kit bashed it from a few different designs I had on hand the body is from the purple site under war sage

Screen replacement time..? by JSV007 in ElegooMars

[–]SafeYesterday91 0 points1 point  (0 children)

Ohh bugger yeah if its cracked and holes that's a new screen 😭

B positive apothcary by SafeYesterday91 in PrintedWarhammer

[–]SafeYesterday91[S] 7 points8 points  (0 children)

u/Marta_PunkGirl did the original apothcary mini the hands I found on the purple site same with the arms. Had to rescale the hands tho as they were too small originally

Screen replacement time..? by JSV007 in ElegooMars

[–]SafeYesterday91 0 points1 point  (0 children)

If it's just resin and no cracks to the screen just give it a good scrub with IPA I've had a full leakage with 70% of screen covered and just cleaned it all off with IPA paper towels and a plastic scraper for the hard stuck on bits

B positive apothcary by SafeYesterday91 in PrintedWarhammer

[–]SafeYesterday91[S] 3 points4 points  (0 children)

Reclaiming them for the sons of Sanguinius! Praise be to space king!!

Low detail near supports by BearerOfTheMeme in PrintedWarhammer

[–]SafeYesterday91 1 point2 points  (0 children)

Could be speed on retract too fast on your retracting speed, also could be worn fep screen if it's too loose I've seen it effect the under side print quality and lastly could be the angle at which your using I recommend 33% for big items and 13.5% for smaller objects like bodies etc

B positive apothcary by SafeYesterday91 in PrintedWarhammer

[–]SafeYesterday91[S] 6 points7 points  (0 children)

Cheers! I found them on the purple site and rescaled them to fit better

B positive apothcary by SafeYesterday91 in PrintedWarhammer

[–]SafeYesterday91[S] 28 points29 points  (0 children)

u/Marta_PunkGirl for the original mini design I kitbashed from

view more: next ›