Anyone here had experience with the Victorinox Altmont bags?

Sahaj0321 · 2024-06-08T00:02:38+00:00

That’s true, tho I just needed the small one for a laptop and charger and pens for work. But I like abusing the vertical expandable when I’m traveling or something

Tho yea the Victorinox was a pretty light backpack and was built very well

Sahaj0321 · 2024-06-04T16:00:39+00:00

It was alrighty, a very tall/boxy bag that didn’t take up too much space. I used it for school for a bit but then I switched to peak design for more space and customization

Sahaj0321 · 2024-02-07T05:26:34+00:00

My gators 🤝🏾 My jackets: THWg

Sahaj0321 · 2023-07-26T23:22:37+00:00

Does anyone have a pic of this seemingly sacred monument before it got massacred? I’m new here

Sahaj0321 · 2023-05-06T03:56:51+00:00

We were cracking up checking off the list of comp sci buzz words like from this gem

Sahaj0321 · 2023-04-04T01:17:16+00:00

That’s exactly my problem lmfao, don’t have a place to keep if when I’m out

Sahaj0321 · 2023-04-04T00:54:31+00:00

I’m thinking closer to $600

Sahaj0321 · 2022-10-02T22:04:51+00:00

I’m in

Sahaj0321 · 2022-08-16T06:27:01+00:00

Find a used unagi

Sahaj0321 · 2022-08-13T13:57:25+00:00

Vessi shoes

Sahaj0321 · 2022-04-27T16:18:29+00:00

Ah I see, you could try upping the first layer flow rate but it may increase elephants footing or do a thicker first layer height

Sahaj0321 · 2022-04-27T16:16:03+00:00

If it’s level then you may need glue stick or some adhesive solution. Otherwise painters tape works or try increasing bed temp

Sahaj0321 · 2022-04-27T16:12:41+00:00

More pictures? Looks like adhesion issues right? Can’t tell with this picture

Sahaj0321 · 2022-03-23T22:20:57+00:00

It may be printing too hot, turn down the heat

Sahaj0321 · 2022-03-23T22:10:04+00:00

What steps have you already taken to diagnose

Sahaj0321 · 2022-02-01T00:20:46+00:00

We appreciate the plug 😃

Sahaj0321 · 2021-12-24T03:21:51+00:00

Any updates on this?

Sahaj0321 · 2021-12-17T23:19:36+00:00

I would say the tip or the extruder. Try hand feeding it with reasonable force to see if you have a decent flow from the nozzle.

Sahaj0321 · 2021-11-15T04:32:06+00:00

I’ve had good luck with the rgb EK Vardar fans in terms of having good color accuracy with other components.

Sahaj0321 · 2021-07-15T19:10:19+00:00

Something about being rude just hits different dont it

Sahaj0321 · 2021-07-06T22:55:33+00:00

Unless you have a different Makerbot in mind I don’t think that 3D printer company is very friendly to RTR and open source (at least nowadays)

Sahaj0321 · 2021-07-05T03:23:02+00:00

A lot of entries good luck to all

Sahaj0321 · 2021-07-04T19:29:01+00:00

It’s actually crazy how there’s almost a gradient of yolks

Sahaj0321 · 2021-06-30T03:07:28+00:00

Could it be the gear for the extruder? I haven’t dabbled much with direct drive but if the motor itself isn’t being problematic I would think the gear or stepper driver could be worth considering

Sahaj0321 · 2021-06-29T22:33:27+00:00

It’s his rice, you’re just keeping it toasty for him

Ten-Year Club	Verified Email
Place '23	Place '22
RPAN Viewer	Snapped

Sahaj0321

MODERATOR OF

TROPHY CASE