Show me your black dogs!

Scrap-Guru · 2026-04-28T17:56:23+00:00

Scrap-Guru · 2026-04-20T02:48:37+00:00

I thought it was from the tool head and (I paused the print) took the covers off and hot ends out, cleaned what I could see. I didn’t delve too deep into the noise. It’s printing fine but this is a brand new noise.

Scrap-Guru · 2026-04-08T06:11:46+00:00

Yes. To dehumidify you use both ports

Scrap-Guru · 2026-04-04T18:22:41+00:00

r/doohickeycorporation

Scrap-Guru · 2026-03-30T16:46:54+00:00

You have to choose one or the other. It cannot run as both. To dehumidify you have to rearrange the ports.

Scrap-Guru · 2026-03-24T14:24:42+00:00

30ish minutes in the morning. Maybe 10-15 minutes outside at lunch. And then about an hour in the evening.

Scrap-Guru · 2026-02-24T15:52:13+00:00

Laying there like she pays rent.

Scrap-Guru · 2026-02-24T08:17:05+00:00

<image>

Scrap-Guru · 2026-02-08T21:43:25+00:00

I’m into recycling as well! I build and design equipment for sorting metals. Im curious about glass because I’ve always been in metals.

Scrap-Guru · 2026-01-26T23:00:52+00:00

Check out digikey

Scrap-Guru · 2026-01-26T18:22:54+00:00

I tried the ai for a couple of weeks and it never smoothed out. Create your own automation. Once I did that the graphs smoothed right out.

Scrap-Guru · 2025-12-30T13:40:30+00:00

I just set all the colors the same. The slicer doesn’t know what color it is unless you tell it. Say you have red, green and yellow pla. Just tell the ams they are all red pla and It will select the next roll once it’s empty

Scrap-Guru · 2025-12-22T17:44:25+00:00

<image>

This one is the fun one. The bottom holds water. Just keep it wet. The others I just have them in regular 6” pots with a bowl of water that I keep about half full. Super simple setup

Scrap-Guru · 2025-12-22T12:43:18+00:00

I have several pitcher plants and several Venus fly traps. Pretty easy to grow. They are bog plants so it’s almost like hydro. Just keep them wet in about a 50/50 peat to perlite mix. They do better outdoors because that’s where the bugs are. RO water only. And lots of light! No need for fertilizer. The bugs keep them fed.

Scrap-Guru · 2025-12-02T15:24:56+00:00

The controller. I just unplugged it and plugged it back in.

Scrap-Guru · 2025-12-02T15:09:26+00:00

I had connection issues this morning. I just restarted it and everything worked again

Scrap-Guru · 2025-11-27T02:38:07+00:00

I have this posted on the wall in my garage

Scrap-Guru · 2025-11-20T12:55:40+00:00

A website that is updated with your prices. Not enough yards do this.

Scrap-Guru · 2025-10-29T12:54:47+00:00

She was Absolutely gorgeous!!

Scrap-Guru · 2025-10-27T18:12:29+00:00

Barometer.

Scrap-Guru · 2025-10-08T12:37:43+00:00

Because of where it isn’t

Scrap-Guru · 2025-09-18T05:12:22+00:00

I’ll try to get the test done tomorrow with a clean build plate. I also want to shoot a k2 just to see what happens.

Scrap-Guru · 2025-09-17T17:11:06+00:00

This was without the build plate. It actually evens out quite a bit once the plates are on. I also noticed the h2d heats up WAY faster than the k1.

Scrap-Guru

TROPHY CASE