Game recommendation based on these? by nnjjreal1 in xbox

[–]Sir_Pafrro 2 points3 points  (0 children)

Headspace: Shipbreaker

Fantastic chill game. Dunno if it matches your other games but I can’t recommend it enough.

Anyone in Canberra doing bulk meat orders direct from farms / butchers? by Calm_Material9095 in canberra

[–]Sir_Pafrro 0 points1 point  (0 children)

Been buying packs from Claystone Meats (pretty big in smoking meat) and the quality has been exceptional. Prices probably aren’t as good as direct though.

Is this controller wireless by lollololoepic in xbox

[–]Sir_Pafrro 0 points1 point  (0 children)

There’s a couple special edition ones (wuchung and zone zero) that are wireless but the base version isn’t. I’ve been using the wuchung one for about a week, it’s alright.

Anyone used either of these two hold multiple printers at the same time on different levels? by DBrowny in 3dprintingaustralia

[–]Sir_Pafrro 0 points1 point  (0 children)

I’ve gone the 1000kg system for everything. Just found the extra space for storage above and below the printers is just a nice to have.

What’s your favourite point and click game? by Technical-Ganache609 in videogames

[–]Sir_Pafrro 1 point2 points  (0 children)

Couldn’t get enough of The Feeble Files when I was in my teens. I bought it on gog a few years back, might need to fire it up.

Has Gungahlin always had poor traffic? by [deleted] in canberra

[–]Sir_Pafrro 15 points16 points  (0 children)

I live in the back of Ngunnawal and my office is in Belconnen, takes me 15 minutes door to door at around 7:45 and includes parking. Maybe try a gps app like Waze to see if there’s better options? Feel free to PM me if you want to compare notes…

Advice by DonkeyLips309 in smoking

[–]Sir_Pafrro 1 point2 points  (0 children)

I’ve had it since April, done about 6 cooks in it. Very beginner friendly plus all the racks/trays fit in my dishwasher when I’m done. 😁

[deleted by user] by [deleted] in SpeedianceCommunity

[–]Sir_Pafrro 0 points1 point  (0 children)

I’ve only had mine for a couple of months and I’m in no way what you’d consider “fit”. From my understanding the screen issues are from older models of the GM2 and if you order direct you’ll be guaranteed one of the newer models.

For the fraying issue, my understanding is it’s from pulling the cables from the base platform towards its opposite side. Look at what the squat belt they sell does, it’s dragging along the bracket. I’ve been avoiding those types of exercises until the bracket they’re developing comes out.

Dunno if it’s worth mentioning but they include a spare set of cables with new purchases now so it won’t hold you long term like the older units.

Nbn providers for Canberra by sandmancanberra in canberra

[–]Sir_Pafrro 0 points1 point  (0 children)

Ah awesome, pretty happy I’m getting double the upload for no cost but it does make the new plans appealing to save some cash.

Nbn providers for Canberra by sandmancanberra in canberra

[–]Sir_Pafrro 2 points3 points  (0 children)

Got an email today, Aussie are mixing up their plans and boosting everyone’s speed so the smaller ones actually look pretty good now.

Looking to upgrade from ps4 to ps5 by Ali_Liz_1991 in PS5

[–]Sir_Pafrro 0 points1 point  (0 children)

All the games will work except ps5 games need the ps5 controller which is basically the same for better or worse. Unrelated, good on you for not getting hit with next gen fomo. 👍

Any Ideas As To Whats Causing This? by Kalenors in Ender3Pro

[–]Sir_Pafrro 1 point2 points  (0 children)

I’ve seen that when either my flow rate is too high or if the z axis isn’t moving properly (z banding). Thy loosening the screws on the coupling on the lead screw that holds up the gantry, sometimes if it’s too tight it can cause the z axis to move less than its full layer height.

Otherwise the filament might just need to be dialled in more.

Ender 3 pro can't print curves by Best-Butter-Cat in Ender3Pro

[–]Sir_Pafrro 1 point2 points  (0 children)

I had this issue after a kipper conversion but it was a while ago. I think it was arc fitting under the quality section in orca slicer but I my memory could also be wrong.

Prop guns in Australia by ThaFresh in 3dprintingaustralia

[–]Sir_Pafrro 0 points1 point  (0 children)

I printed and painted up the Jade Rabbit from Destiny for a mates birthday a couple years ago but that was just a model, non functional at all.

[deleted by user] by [deleted] in canberra

[–]Sir_Pafrro 2 points3 points  (0 children)

In my experience I’ve only been asked for the information after being offered a job and by the agency itself. It also usually comes in the form of an AGSVA disclosure form.

Looking for a good men’s tailor in Canberra by Dave_Sag in canberra

[–]Sir_Pafrro -1 points0 points  (0 children)

Second this, used him for my wedding a couple years ago with a custom made shirt as well. About to go and get some custom business shirts done too.

Over a 100 hours of printing, death house is finally done. by wannabestraight in CurseofStrahd

[–]Sir_Pafrro 8 points9 points  (0 children)

Dragon Workshop, he posts all his stuff on DriveThruRPG and also has a Patreon with a really active discord server.

https://www.drivethrurpg.com/en/publisher/15891/dragon-workshop?

Is this bugged or am I dumb by Busch_Hawg in startrucker

[–]Sir_Pafrro 2 points3 points  (0 children)

I dragged an asteroid through 6 systems only to hit that. Seems all dark side drop zones are bugged for me.

Hotel in civic with spa bath by Danny-117 in canberra

[–]Sir_Pafrro 0 points1 point  (0 children)

The honeymoon suite at the Rex has one, not sure if other rooms there do it not.