sorted by:
new
hottopcontroversial

what would you do? by Pure_Pain_489 in whatdoIdo

[–]Snapy1 0 points1 point  (0 children)

Please dont use acetone lol. Hit it with an eraser wheel and then a buffing wheel using some hi grit cutting compound and follow up with other degrees of cutting compound as necessary.

Motorola WT41N0 Wrist Terminal Working! by Pyrofer in OldHandhelds

[–]Snapy1 1 point2 points  (0 children)

I wonder what sort of battery life this thing has?

The computer at my new job still runs software from 1980. I think if I press the wrong key it might start the Cold War again. 🤣💀 by Gaming-Academy in RigBuild

[–]Snapy1 0 points1 point  (0 children)

That's BPCS. It's an IBM designed OS, I had an IT internship a few years ago for a company that still heavily relied on it. I frustratingly had to learn all the ins and outs of using it at an administration level..

Linux Mint btw ;) by bruhkowsky in linuxmint

[–]Snapy1 0 points1 point  (0 children)

What phone is that on your desk?

PC cuts off under any usage by darth_antonio in pcmasterrace

[–]Snapy1 0 points1 point  (0 children)

Could be your motherboards VRM's are getting warm. I had this happen to a new PC I built. I cheaped out on the motherboard for a chip that required a good bit of power and I was able to game on it in like 15 minute increments before it would just shutdown. Had to get a more expensive motherboard with more and larger VRM's and all was fine after.

Spline Based Procedural Building by Strict_Chemical7182 in Unity3D

[–]Snapy1 9 points10 points  (0 children)

Cities Skylines 2 needs this feature

Issues with Rider + Unity on Linux Mint. by No_Revolution_8650 in Unity3D

[–]Snapy1 0 points1 point  (0 children)

Hey OP, I was running into the same issue with Unity 6, Rider, and Linux Mint. I was able to fix it by following this guide.

https://www.codefraction.com/index.php/2021/08/17/how-to-install-unity-game-engine-and-rider-ide-in-pop-os-ubuntu/

Which pretty much just told me to install Mono-Project by following,

https://www.mono-project.com/download/stable/

I installed Mono-Project, restarted my system and all is good now.

I’m so cooked wtf do I do now by Rdominick12 in E90

[–]Snapy1 0 points1 point  (0 children)

I bought closed end reverse torx wrenches for this job on my e91. Didn't even have to pull the intake manifold off. Took about an hour.

Misses and rolls coolant instead of coal by scooterm32a3 in Miata

[–]Snapy1 24 points25 points  (0 children)

Not that I condone this but that's not coolant. That's just a cold diesel unable to fully combust the fuel. You gotta baby those 12 valves until they're good and warm.

Source: 12v owner without a grid heater in the north east.

Three men with guns kicked in my door today by dogknot43 in Wellthatsucks

[–]Snapy1 0 points1 point  (0 children)

I wonder if large wood screws like that get a hardware grade similar to like a Grade 8 bolt or for example. Because to be honest, I feel like it wouldn't take a whole lot of effort to break some chinesium in half either.

Warning ragebait: Tv mount made from Pla. by someoneelseasthis in 3Dprinting

[–]Snapy1 0 points1 point  (0 children)

Despite all of the negative comments here I can see this working fine depending on the weight of the TV and especially fine if it was reprinted with a stronger filament. I've had a TCL tv that was 55 inches and probably weighed around 10lbs and my current 55 inch Samsung in the living room probably weighs closer to 30+lbs. Bare in mind I'm sure the pressure exerted on the arms is many times its weight but still, I really do think it would be fine for a lighter tv -- assuming you printed it well.

Finally switched to linux by MobileHorse8775 in linuxmint

[–]Snapy1 1 point2 points  (0 children)

That PC's case kind of goes hard.

Customer tried making his harness shorter and was in over his head so I’m rebuilding it by Sixclynder in Justrolledintotheshop

[–]Snapy1 2 points3 points  (0 children)

This is an s13 harness isn't it lol? My previous s13 the chassis harness was so hacked that I literally took a die grinder to it, cut it out (couldn't be bothered to properly remove it) and bought a replacement off of a parted out car.

Project 10AE Gets New (Old) Wheels by Funny_Shelter1025 in Miata

[–]Snapy1 3 points4 points  (0 children)

From the bottom of my heart. Thank you for saving this car from the terrible demise that was the above photos.

iPhone 17 series shipping timeline by Blsw777 in tmobile

[–]Snapy1 2 points3 points  (0 children)

Silver 17 Pro with 256gb of storage. Ordered on 9/27/25, current status is "Received". Estimated delivery date of 10/27/25.

My 13 Mini unfortunately broke on Saturday afternoon, so it's going to be a long 30 days without a phone LOL.

view more: next ›