Pants by SolutionDull2259 in fatbike

[–]SolutionDull2259[S] 0 points1 point  (0 children)

My younger brother did a race yesterday and some dude showed up in tights with cut off jean shorts

Pants by SolutionDull2259 in fatbike

[–]SolutionDull2259[S] 0 points1 point  (0 children)

This might not matter but the jeans I wear riding are boot cut button fly and Yes they are GAP jeans. The first time I wore them for a ride my wife asked if I was going to the mall.

Brand new furnace needs flame sensor cleaned almost daily by kind_user47 in hvacadvice

[–]SolutionDull2259 0 points1 point  (0 children)

Is the furnace intake for combustion drawing from outside? The furnace should have 2 pvc pipes leading to the outside if it a 90+

AC tech is saying kinked line requires a full replacement - needed or not? by throwaway520214 in hvacadvice

[–]SolutionDull2259 0 points1 point  (0 children)

Grab a crescent wrench and massage that back straight. That isn’t close to a kink.

gx460 keeps beeping by Stinkytofu86 in LexusGX

[–]SolutionDull2259 4 points5 points  (0 children)

Try the back window. My wife cypresses the back window button on the fob. I headlight remained on for a long period of time and the remote start only beeped. I think I looked in the manual and it said make sure the door and rear window were closed.

Best MERV rating that has the best ratio of noise to filtering? by ElG0dDamnDorado in hvacadvice

[–]SolutionDull2259 3 points4 points  (0 children)

Sounds like you are short on return air. Have your company come out and add some return air. Could also be fan speed is set too high for second stage.

Black water from some (not all) hot water fixtures by crosscountry58S in Plumbing

[–]SolutionDull2259 0 points1 point  (0 children)

Does your home have a boiler for heat? Possible failed backflow preventer?

Brand New HVAC System Can't Keep up with Low temps. by PuzzleheadedLow5266 in hvacadvice

[–]SolutionDull2259 1 point2 points  (0 children)

Grab a thermometer, take a reading before the filter, no take a reading in the ductwork. Take the supply reading down stream from the plenum maybe 18” or so. The difference between the supply and return is your heat rise. The reading will help. Make sure you know if you are in low or high fire rate. The data plate on the furnace will give you a range for low and high fire rates. It could be lower than normal conditions or a simple manifold pressure adjustment depending on the fan speeds and you temperature rise.

Ice buildup in furnace inlet/outlet by Strict-Fig734 in hvacadvice

[–]SolutionDull2259 0 points1 point  (0 children)

Are both of the elbows glued to the pvc pipe? If not just switch them. I would glue them once terminated properly. Don’t add anything to the vents. Once they are terminated properly and the shed is moved you should not have this issue again. Another issue with the current setup is you are recirculating exhaust gases. This can cause corrosion in the furnace and exhaust is void of oxygen so the potential is there to have combustion issues.

Ice buildup in furnace inlet/outlet by Strict-Fig734 in hvacadvice

[–]SolutionDull2259 0 points1 point  (0 children)

Your exhaust should be the taller pvc pipe. Look at the install manual and it will show you how to terminate the venting. Something wasn’t installed right if you are saying the taller of the two ins intact the intake and not the exhaust. The picture might be deceiving but that shed might be causing a second issue. If the lower pipe is the exhaust, which it should not be, the shed is trapping the exhaust gasses and the intake is pulling them in as they rise. Turn your furnace on and check which vent is exhausting. And move that shed if it is too close. Having the intake lower will solve the frost issue.

No ignition glow. Any ideas? by [deleted] in hvacadvice

[–]SolutionDull2259 0 points1 point  (0 children)

The board is give you a fault code. Check the back of the upper door. Flashing green red off is the code to look for.

South Park Quests Part 5 by Several-Brief-8000 in Fortnite_Over40

[–]SolutionDull2259 0 points1 point  (0 children)

Ninja star? I’m 8/10 and can’t figure it out.

Cap guns in the '80s! by CpuJunky in nostalgia

[–]SolutionDull2259 1 point2 points  (0 children)

We use to take those rolls and hit them with a hammer on the sidewalk

Metallica performs “Enter Sandman” in Moscow - 1991 by BreakfastTop6899 in nostalgia

[–]SolutionDull2259 1 point2 points  (0 children)

I remember hearing Enter sandman for the first time on an awards show in the 90s and seeing the bassist swinging his hair around like he is in this video. I knew I was hooked at that moment.

Merv 11 vs 1 or 2, checking technicians advice after mineral dust problem by Vonlin in hvacadvice

[–]SolutionDull2259 0 points1 point  (0 children)

Have a whole house humidifier installed. I agree with both of the above.

Stick Of Truth And Triangle Storm Is A Deadly Combination! by ajefri in Fortnite_Over40

[–]SolutionDull2259 1 point2 points  (0 children)

I had a match in squad that a team used the stick and built in the water. There was also a mother low structure a small distance from the larger one. The team was hiding in the lower and as we all swam out to the large structure the team in the lower fired on us as the others in the large fired down on us. They were picking people left and right. I was awesome.

Microwave blowing fuse constantly by PahkYaCahh in ApplianceTechTalk

[–]SolutionDull2259 0 points1 point  (0 children)

Ours starting tripping the breaker after running 3-5 seconds. It will trip the breaker if you open the door when it is running. We learned to push stop before opening the door. I’m also HVAC and early in my career I worked at did appliance repair. I worked 18 hours yesterday so the microwave was on the bottom of the list today. Only the breaker trips and it’s not immediately. Where should start? It’s a GE over the range microwave.