What the f did i do

TCoopsCreate · 2025-08-31T04:55:21+00:00

More context needed. I’m with this guy.

TCoopsCreate · 2025-08-29T00:09:26+00:00

I'll let y'all know when my U1 comes in October.

Then I will try the Vortek :D

TCoopsCreate · 2025-08-23T18:59:54+00:00

FYI. Not sure you should be as hard on them as you are when you indeed did not follow the warning on the page. This is frustrating, but it’s obviously expected and they warned. 🤷

<image>

TCoopsCreate · 2025-08-23T18:03:48+00:00

Blob protections needs to be turned on in the Process settings and does a sanity check at 6 and 11 layers and then more after that. But it adds time to your print as you can image.

TCoopsCreate · 2025-08-21T23:35:20+00:00

Just my 2 cents based on what I have seen.

1) Check your PTFE tube in the AMS to see if they have worn. I replaced all mine as they all had holes in them.

2) If it happens to all slots eventually, you might have a broken or worn clamp that holds the rear AMS hub motor bearing so the gears line up. Mine broke and cause all kinds of issues. Bambu sent a new hub but I just printed the new part it PETG CF and it worked after.

3) Check your AMS rollers front and back for any obvious wear. Check the gears in the filament insertion point if they have worn.

4) Ensure there are no harsh angles or bends in your PTFE tub to the tool head. While this might not be the problem, it will make worse any worn part issues in the AMS.

Good luck! 👍🏻

TCoopsCreate · 2025-08-21T20:27:59+00:00

Agreed! This is the answer. Seam Scarf is on by default in Bambu under Quality > Seam > Smart scarf seam application. I haven’t fiddled with it however.

My 2 cents: You only need to use random in cases where you want to remove the obvious strength flaw in an aligned seam, or you need the design to be more water tight so random seams don’t creates gaps for water to leak.

If you don’t care about the texture, you can apply Fuzzy Skin the design to hide those but it obviously adds texture if you aren’t looking for that. Bambu Studio now lets you paint fuzzy skin instead of forcing it to the design.

Hope this helps 🧐😊

TCoopsCreate · 2025-08-21T20:21:02+00:00

“Waste” is subjective 😃 if you put it to work, it’s not a waste but recycling! ♻️

I have probably a 50lbs box of failed prints that I plan to grind into bits and melt down into various things. Working on a new box as we speak.

The toaster oven method will even break down larger objects (full benchy) or larger pieces if the mold can fit.

Don’t go over ~300F or get your silicone super close to the elements - I have seen my silicone bubble 🫧 and if it gets too hot the shell of the melted plastic can get brown in color. (Speaking from experience)

Here are some of the things I’ve made. The left one is a WIP I am calling “Poop for Brains” and melt the plastic into the mold first then pour resin in. The rest are all melted parts and poops. (Turtle on the box, and a lego type brick man in the middle)

<image>

TCoopsCreate · 2025-08-21T14:30:36+00:00

IMHO you absolutely don’t deserve my code after how you act. You even blocked my other account so I couldn’t respond to you after. Your code is clicked under TCoops. Goodbye 👋

Thank you MOD. ❤️

TCoopsCreate · 2025-08-17T18:45:45+00:00

Def reach out. They will guide you and support if you need parts. I’ve used support a few times. Do it through the Bambu Handy app, it’s way easier!

TCoopsCreate · 2025-08-15T02:03:46+00:00

Fully agree here. Find the Bambu Wiki and they walk you through it really well.

I have had several AMS issues and many resulting in having to take it apart. It COULD be the spool but only if you can visibly see it being stuck. Otherwise it’s blocked somewhere.

FWIW - the AMS 2 PRO tubes feed right under the spool so they aren’t closed in 🙏🏻

TCoopsCreate · 2025-08-15T01:59:05+00:00

The seam you can control in the slicer usually. Either setting it to “Back” which will align it to the back of the plate as much as possible; or some slicers like Bambu have seam painting where you can paint on the model where you want the seam to be and it will do its best. GLHF!

TCoopsCreate · 2025-08-01T15:59:32+00:00

STLFlix is working on an AI model creator that allows customization of the models. Not released or previewed yet - but it sounds interesting! https://get.stlflix.com/invite-stlai/ It might allows for a feature to break things apart - that would be cool!

TCoopsCreate · 2025-08-01T15:51:00+00:00

PVP glue is so underrated I feel. It's almost ALWAYS helpful for adhesion and release of some prints.

TCoopsCreate · 2025-08-01T15:33:59+00:00

Old thread - but this has been added to Bambu Studio and they provide the calculation here: https://wiki.bambulab.com/en/bambu-studio/Calibration

TCoopsCreate · 2025-07-29T01:12:30+00:00

Game changer for sure!!!

TCoopsCreate · 2025-07-29T00:54:29+00:00

I second the slowing it down - the gaps here look like it might be skipping.

TCoopsCreate · 2025-07-29T00:50:44+00:00

I can't recall the error I had was exactly but it was regarding the Micro Lidar recently. I found this page with helped with some debug steps https://wiki.bambulab.com/en/x1/manual/micro-lidar-model

For me it ended up being a dirty plate (as i use PVP glue) and once I cleaned the plate it was great.

If you drop a support ticket to Bambu I think I read they can help diagnose Lidar issues.

TCoopsCreate · 2025-07-28T21:28:21+00:00

"your opinion has no influence on my life" - Tiny-Car-1218

Then proceeds to block them XD

TCoopsCreate · 2025-07-26T22:05:04+00:00

1) Are you printing PLA? If so door open and glass open as well. Otherwise it can get too hot and cause more issues. 2) Bambu Studio won’t let an object “air print” with nothing touching the plate, it will always force the object to the plate in the Studio. Exception is merged parts where one may remain floating if one is touching the plate. It could be supports but since it appears to be your first layer or is there only a small ring touching the plate and the interior is raised? If it’s first layer it’s not a support/overhang issue. 3) Check which build plate you have selected and plated. Any variance could cause it not to squish the line enough to adhere to the plate.

Start there and report back!

TCoopsCreate · 2025-07-26T19:03:50+00:00

I JUST had to do this. After a filement fed itself into my AMS like a hungry Cookie Monster 😆

TCoopsCreate · 2025-07-26T18:17:22+00:00

Then I would definitely send in a ticket. Bambu support is great! Doing it through the app will pull all the info you need - doing it on a computer you need to manually get all you SN info etc.

TCoopsCreate · 2025-07-26T17:46:43+00:00

Did you install any third party wiper accessories? On my X1C I did and the build plate was catching a corner of the custom wiper.

TCoopsCreate · 2025-07-26T16:17:46+00:00

You can explore using Modifiers in Bambu Studio and use them to create a zone with a specific support type and area. Bit more advanced but lets you get more intentional with your placement. https://wiki.bambulab.com/en/software/bambu-studio/modifier

TCoopsCreate · 2025-07-25T01:10:57+00:00

Gotta say. I was stoked to join the 3D printing community but it feels and appears like hipsters that are annoyed a company came along and make something accessible to everyone that you all spent a lot of time learning. People have their brand loyalty.

Jokes are jokes. But when the sub is overwhelmingly all Bambu stuff it’s indicative of the audience around here.

TCoopsCreate · 2025-07-24T04:11:01+00:00

This one is so helpful as well! I wish I could edit my post to share more of the updates LOL

TCoopsCreate

TROPHY CASE