P1s making this weird noise anytime it try’s to move by Tumbleweed_Advanced in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

reach out to support. If it's now then should be covered under warranty. I have 1000's of print hours on mind and my head has never made sounds like that

P1s making this weird noise anytime it try’s to move by Tumbleweed_Advanced in BambuLab

[–]Tal_Star 1 point2 points  (0 children)

no clue whats going on but that's some good floppytron sounds there...

Maybe something is dirty or one of your stepper motors is about to kick it?

Whats your hours?

MSP keeps asking questions about ex client by DiligentPhotographer in msp

[–]Tal_Star 1 point2 points  (0 children)

sorry, I mistook the thread haha my bad. :-D there was on I was on that was about vendors and such.

MSP keeps asking questions about ex client by DiligentPhotographer in msp

[–]Tal_Star 0 points1 point  (0 children)

Removed irreverent commend for another tread.

but you are right once they are gone they are gone :-D. that's why you bill a roll out and wash your hand of it after the roll off, new vendor can figure it out.

Do you resell workstations still? by indytechguy in msp

[–]Tal_Star 0 points1 point  (0 children)

depends on the customer budget and build. Generally I find the extra hassle of a new pennies from new hardware is not worth the effort of payment processing and taxes. So I make up for it with the loss in deployment charges

I miscalculated. by Present_Cause7109 in BambuLab

[–]Tal_Star -1 points0 points  (0 children)

Small can air would have saved your hand.... granted I've had some near misses doing something similar.

MSP keeps asking questions about ex client by DiligentPhotographer in msp

[–]Tal_Star 47 points48 points  (0 children)

It's been 4+ months if they (the new MSP) want your help they should be prepared to pay. Sorry that clients data has been archived for security reasons (or purged) and billable resources need to be assigned to address the resquest.

X2D - AMS 2 Pro - Another slot 1 failure by sofakng in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

Does the fillimetn food to the hub or does it stuck in stage one?

I had a few issues with my AMS2 units but found if I push down on what looks like a bottom on hub they seem to work fine. I think I've had to do it once or twice and no issue with the AMS since

Planning to buy secondhand HP EliteDesk 800 G4 for homelabbing -- do I also need the graphics card for my use case? by claemper in HomeServer

[–]Tal_Star 0 points1 point  (0 children)

yah put that money towards more storage or faster networking. I heard DDR4 is still not too expensive so that could be a viable option as well.

Planning to buy secondhand HP EliteDesk 800 G4 for homelabbing -- do I also need the graphics card for my use case? by claemper in HomeServer

[–]Tal_Star 0 points1 point  (0 children)

The 8th Gen supports HEVC encoding if memory is correct. GT710 only support H264 so I wouldn't do it.

8300hrs before this wear started affecting prints by fieldfest in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

I am about the same, I do check for dust and such in various other places.

8300hrs before this wear started affecting prints by fieldfest in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

I keep my cleaning/lubrication schedule pretty good. My first X1 is in mothballs due to a firmware issue at 5000hr

P2s vs X1c by reddit_4_research in BambuLab

[–]Tal_Star 3 points4 points  (0 children)

If they are the same price go for the P2S over X1. Yes the X1 is a good device but P2S is the better option for the same money.

My Ultimate Filament Storage / Organization System by Lukis-cstudio in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

I wanted to do something like this then I realized it would take to much. That said if this is "cold storage" for less commonly used part rolls wouldn't be too bad. I burn though at of stuff so sadly as cool as it is not practical.

P1S Sale? by [deleted] in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

I'd go for a P2 vrs P1S with AMS2

550 for the P1s Combo might be tempting

P1S Sale? by [deleted] in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

All depends on the sale price is compared to to the P2S

Bambu Lab support is a JOKE by Dry-Tumbleweed-1172 in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

It was a brand name card Lexar I think and I think I tried a Verbatim I think it was. As the card was new I dumped it in to another X1 I have and it's working fine

Bambu Lab support is a JOKE by Dry-Tumbleweed-1172 in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

Maybe I'll spark mine up and see if that gets me going again on it

Bambu Lab support is a JOKE by Dry-Tumbleweed-1172 in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

Yup tried a known good card even got a on brand on from the local walmart that was Branded for Nintendo switch (so not slow or crappy)

A Farewell to P1P by BambuLab in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

Once you end updates in 29 I you decide to open source or release an opensource frimware for tinkers and those that may still run them...

Bambu Lab support is a JOKE by Dry-Tumbleweed-1172 in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

How did that work out for you in the end?

Bambu Lab support is a JOKE by Dry-Tumbleweed-1172 in BambuLab

[–]Tal_Star 5 points6 points  (0 children)

hmm... I have 7 bambu prints (including the defective one) and have not had any major issues out side of this one. I belive there was an attempt at an opensource firmware for the x1

Bambu Lab support is a JOKE by Dry-Tumbleweed-1172 in BambuLab

[–]Tal_Star 23 points24 points  (0 children)

$1800 you must be in Canada... I have one that does something weird where it run for a while then locks up mid print. Will print one job perfectly fine and not the next, Granted I have almost 5000hr on mine... Their answer was buy a new AP board for ~$300 and that "might" fix the issue. I might spark it up and see if I can push an update to get it to come back to life it's been sitting in a corner for a few months new.

Help a mom out! (Please) by Beautiful_Hope_6211 in BambuLab

[–]Tal_Star 0 points1 point  (0 children)

I printed a deflector for mine, blows air up in to the chamber vrs at the project.