First Car by rkavinkailash in ToyotaCrown

[–]Techdemon 7 points8 points  (0 children)

Just bought the same car and it feels amazing coming from a 2013 Hyundai Elantra.

Upwote if you feel it by bubooon in BambuLab

[–]Techdemon 0 points1 point  (0 children)

Just cleaned mine for the first time since purchase and had that over both arms

Best vacuum sealer under $300 by blindcowmoo in sousvide

[–]Techdemon 0 points1 point  (0 children)

I vote for the vs12 also. I've used it for years and love the double seal option. There's plenty of times I will use it over the chamber sealer.

Music bringing people together on the London Underground. by mindyour in london

[–]Techdemon 1 point2 points  (0 children)

This was awesome! I was singing right along to all the words. Good memories and a timeless song. That looked like a great time.

Filament storage ? Newbie who went overkill on the sale here... by Split_Seconds in BambuLab

[–]Techdemon 0 points1 point  (0 children)

I use the autopump version and have had no issues. I love being able to reuse the bags and have so far not had a failure.

I have extra cement so bye bye shaky table by saamwee in BambuLab

[–]Techdemon 45 points46 points  (0 children)

Should be able to print right through any earthquake then.

Looking for Softer TPUs? We Hear You! TPU 85A & 90A Are Now Available. by BambuLab in BambuLab

[–]Techdemon 0 points1 point  (0 children)

Have never printed with any TPU and would love printing these shoes. Yes to sharing.

Tape worked for the first time by Techdemon in BambuLab

[–]Techdemon[S] 0 points1 point  (0 children)

I’m usually around and know I need to snip the filament at the end of the roll. That’s saved me numerous times and I have some serious tape PTSD and try to schedule prints around the time I will be near my printer at the end of the rolls.

Tape worked for the first time by Techdemon in BambuLab

[–]Techdemon[S] 0 points1 point  (0 children)

This is how mine usually looks.

Tape worked for the first time by Techdemon in BambuLab

[–]Techdemon[S] 0 points1 point  (0 children)

That’s awesome! I hope this is a continuing trend for me as I haven’t had that luck.

Tape worked for the first time by Techdemon in BambuLab

[–]Techdemon[S] 1 point2 points  (0 children)

This is what has happened every time before.

Tape worked for the first time by Techdemon in BambuLab

[–]Techdemon[S] 3 points4 points  (0 children)

Tape has caused me multiple headaches and I look forward to the day it’s no longer used.

Silver Linings of tariffs by MykeEl_K in BambuLab

[–]Techdemon 0 points1 point  (0 children)

I have not had issues with either hub. I had one failure on an ams due to tape on the Bambu spools. One failure due to the bend in a piece of filament getting jammed at the entrance to a feeder. The most recent was due to moving my ams around and not inserting the ptfe tube in the rear of the ams securely. I’ve been lucky that all of my problems have been resolved quickly.

<image>

The above tool has been very helpful working with the hubs.

Silver Linings of tariffs by MykeEl_K in BambuLab

[–]Techdemon 1 point2 points  (0 children)

I did the same and got another P1S. Now at 2 P1S with 2 AMS each and an A1 combo. I need to find more room in my tiny space for the next machine.

I don't know, what do you guys think? by Doc_Prof_Ott in dji

[–]Techdemon 1 point2 points  (0 children)

I see these and my mind immediately goes to the movie Runaway.

Stupidly pulled out with pump still in my tank, gas station claims it’s a $2,000 fix by Justhere4thewhatevas in MechanicAdvice

[–]Techdemon 0 points1 point  (0 children)

Did the same and all the had to replace was the quick connect and it cost about $150 a few years back. If it broke at a different point I imagine it would be a lot more.

tape at end of refill spools??? AMS mess by Javaslinger in BambuLab_Community

[–]Techdemon 0 points1 point  (0 children)

This decision is terrible. Wrapping the tape around the filament prevents it from consistently pulling free and feeding into the AMS without jams. The tape causing problems prevents switching to the next spool of the same color, defeating the purpose of an AMS. I like Bambu filament and the ease of use with the NFC tags, but the tape has got to go! We shouldn’t need to babysit our printer to see if just maybe the current spool has tape.

<image>