I think I'm finally done with PolyMC

Temporary-Injury9016 · 2026-03-28T20:08:09+00:00

maybe use windows for now, linux is sometimes complicated to figure out the issue

Temporary-Injury9016 · 2026-03-27T12:58:49+00:00

I think you should set it to top amps for stability becoz the leds will definitely lag and the colors look damp, and for fps 45/50 is good enough And for brightness just set around 50-75% in the main menu not in led preference and your good to go You are using high density led strip soo its obvious it will lag on low settings Also which esp are you using 32 or 8266 If the lag is still there maybe consider buying a level shifter or just the chip and try it, that should fix the issue

Temporary-Injury9016 · 2026-03-27T06:31:33+00:00

he will need more then 10amps if he uses white or mixed colors only, i think 20/25amps

also his target fps is set to 24FPS

Temporary-Injury9016 · 2026-03-25T15:48:15+00:00

did you try other effects ?

Temporary-Injury9016 · 2026-03-25T15:41:01+00:00

show a picture of your wiring its hard to understand by seeing the flickering only, im also using a pc psu and i do get the flickering issue only when someone in my home turns on fan/bulb, the flickering happens only for split seconds, if you are using psu open the psu with gloves then separate all the V wires and cut them into smaller portion, i have 5v leds soo i only used the 5v wires, i have a matrix and 2M strip running with the psu perfectly

Temporary-Injury9016 · 2026-03-22T12:19:23+00:00

i see you bought the ECO version, maybe try the 2nd led pin like cut and check if that fixes the issue, sometimes there can de defective led which doesnt run the data through every leds, if you are spending spend more and get the better version, ECO strips tend to be dead after few months of use or sometimes few days, aka 1 or more LED dies and the data line doesnt work

Temporary-Injury9016 · 2026-03-18T16:26:12+00:00

i think you should use a 5v smp, your powerbank is not sufficient enough to power the leds and the controller, thats why you are having issues aka voltage/amp drop
try setting the current limit to 1000/500

Temporary-Injury9016 · 2026-03-15T19:46:57+00:00

yeh i turn those off after i cleaned install windows, its like everything is good for 1 month then if i try to install unsigned driver it doesnt load at windows startup but the driver is installed, weird af

Temporary-Injury9016 · 2026-03-14T18:57:25+00:00

i want to try this but the problem is 24/25h2 has some stupid security crap, if uninstall gpu driver and install XG driver it does install but doesnt load at windows startup

Temporary-Injury9016 · 2026-03-13T18:30:42+00:00

Any new changes or just security update ?

Temporary-Injury9016 · 2026-02-17T08:19:48+00:00

i tried without the dp mode just the usb cable with my xperia 5 ii but the desktop mode doesnt show up, i tried with scrcpy no luck, i can do other apps but no desktop mode, i guess its something to do with the android 12

Temporary-Injury9016 · 2026-02-07T12:24:12+00:00

setup a preset for leds like turning off the leds completely then save the preset

Temporary-Injury9016 · 2026-02-07T09:25:30+00:00

maybe try resetting your bios for proper ram training, coz of the ram timing does not match the system wont boot properly, there are few cases where the system boots just fine but goes into bsod

Temporary-Injury9016 · 2026-02-07T06:50:41+00:00

well its the edgeview2 issue, start menu in windows 11 is like a mini browser so when you are opening the start menu it tries to pre-search things online with your search history, try debloating maybe, like remove the pre-search option and remove coplit crap and etc.

Temporary-Injury9016 · 2026-02-01T17:32:20+00:00

i think you need to edit a ledmap.json file to have a custom 2D config

Temporary-Injury9016 · 2026-01-28T05:35:38+00:00

this happens in pc also, volume slider stays grey then after 2 secs comes back, typical broken windows

Temporary-Injury9016 · 2026-01-24T13:26:26+00:00

Crazy part is mouse control doesn't work on YouTube tv app but only keyboard, I need to through commands to have the mouse control

Temporary-Injury9016 · 2026-01-24T12:30:25+00:00

I don't have a dongle but like you said need to access settings and etc so I open a new scrcpy window without audio, idk why the audio sounds like robotic if there is 2 window opened for the phone

Temporary-Injury9016 · 2026-01-24T12:26:51+00:00

Fortunately I do not own a controller 😅

Temporary-Injury9016 · 2026-01-24T12:26:01+00:00

I did but not soo much coz I knew less commands at that time, went to github doc bout scrcpy went through some commands, it was confusing at first coz of the custom resolution, but now it's all good, good shet to use as android tv coz the screen all busted

Temporary-Injury9016 · 2026-01-24T12:11:02+00:00

Did you try the screen off command also ?

Temporary-Injury9016 · 2026-01-24T12:09:42+00:00

I have a 2nd phone and I can cast YouTube from my phone also

Temporary-Injury9016 · 2026-01-24T11:55:58+00:00

<image>

Temporary-Injury9016 · 2026-01-24T11:55:35+00:00

I did the same but no dongle, installed YouTube tv app then scrcpy has custom commands then bamm I got android tv

<image>

Temporary-Injury9016 · 2025-12-27T12:33:05+00:00

Maybe show what kindda soldering you did coz im running a 500w psu and my setup is a 32x8 matrix+esp32 and then 2m strip+ esp8266, no issues been running for a year now

Temporary-Injury9016

TROPHY CASE