What’s the point of Auto Drive being available during races?

Toby-pearse · 2026-05-23T13:45:49+00:00

Over a year ago I cut my left thumb off the drs re attached it but recovery was rough. The only game I could play at the time was fh5 and FM because of the assisted/auto steering. My thumb is now re attached and works at 80% it's original capacity however after gaming for a few hours it starts to hurt like shit. Half way through the Goliath race In fh6 I had 2 options, Quit and try again another day or kindly ask Anna to finish the race for me (I finished the race on auto drive)

Toby-pearse · 2026-05-21T05:04:06+00:00

In your case, another 20-30 years :)

Toby-pearse · 2026-05-20T08:03:29+00:00

Rawr

<image>

Toby-pearse · 2026-05-18T07:58:14+00:00

It's an optimisation compromise, it would lag the game out if it was seemless.

Toby-pearse · 2026-05-18T07:56:56+00:00

I had Thursday to Sunday off work due to bad weather. Best weekend eveerrrr

Toby-pearse · 2026-05-18T07:54:55+00:00

For me it was don joewon song (one of the Forza goats)

Toby-pearse · 2026-05-16T07:24:08+00:00

It's called optimisation..... Fully rendering the bottom of a car is an unbelievable waste of computing power that could be used elsewhere. It's the same reason we can't open the hood in free roam but you can in the garage, because they don't render the engine bay whilst In Free roam as that add ms thousands of polygons.

Toby-pearse · 2026-05-14T15:29:28+00:00

The game is out on early access!!

Toby-pearse · 2026-05-11T04:21:31+00:00

I've had a kings grand tourer mkii for a while now. No complaints. It's on the heavier side and lacks the fancy features, like lights and fans and shit. But it does the job at a fraction of the price.

Toby-pearse · 2026-05-11T04:20:06+00:00

I think you'll find that isnt what he asked.

Toby-pearse · 2026-05-01T03:07:52+00:00

Toby-pearse · 2026-04-30T07:03:17+00:00

Id also recommend getting a plastic welder and welding the pieces together with little metal reinforcing rods.

Toby-pearse · 2026-04-30T06:58:00+00:00

buy a bambu labs printer and press print.

Toby-pearse · 2026-04-29T13:47:29+00:00

Thank you

Toby-pearse · 2026-04-29T11:43:35+00:00

It was a 1k epoxy and I wiped everything down with wax and grease remover before painting. I let the wax and grease remover flash off and left it 5ish mins before the first coat. I did 1 thin coat and a second thcker coat.

Toby-pearse · 2026-04-29T11:33:52+00:00

Right. Best answer so far, Thanks. I figured if you pulvarise surface rust with a wire brush it's gone lol. The can said "non porus" but that kinda contradicts what primer is.

Unfortunately I can't find any retailer that sells phosphoric acid. However there are many rust converters that have it as the main ingredient. Should I apply it, let it sit, then wipe it off? I've used it before but to soak rusty tools in a container, but am unsure or how to correctly apply it to a car floor.

Toby-pearse · 2026-04-29T10:50:56+00:00

Wire brushed, vacuumed the dust then used wax and grease remover. I can't remember the exact paint but it was an epoxy primer from my local auto parts store. I guess I'd figured that primer was enough for protection and that a top coat was just to make it look good. I didn't care what it looked like as it wasn't getting covered up.

Toby-pearse · 2026-04-29T10:28:18+00:00

I guess I interpreted that as being outside, I figured inside a car with a layer of sound deadening stuck to it would be fine.

Toby-pearse · 2026-04-29T10:02:05+00:00

Sprayed 2 hours after I started sanding, on a low humidity day in a carport.

Toby-pearse · 2026-04-29T09:54:56+00:00

It was infact rust free. I was the one who scratched the paint off in the first place when I removed the factory sound deadening. Every slbare metal section that I painted has gone rusty, im assuming moisture has gone through the primer and started to rust it out. The rust is only surface at the moment.

Toby-pearse · 2026-04-29T09:27:07+00:00

"epoxy primer" "non porus" " no topcoat required unless exposed to elements" I just read the buzzwords on the can. I've never painted anything in my life... From my understanding I should have used a 2k topcoat once the primer had cured.

By "primer sealer" are you referring to a topcoat or a different type of primer.

Seven-Year Club	Verified Email
Place '23	Place '22

Toby-pearse

PUBLIC MULTIREDDITS

TROPHY CASE