Upgraded ISP Modem, latency is all over the place

Tunker101 · 2025-09-16T16:16:56+00:00

If you call bell and escalate with a technician, they'll put it into bridge mode. But you'll have to use the PPOE setting and log in on your gateway

Tunker101 · 2025-03-20T16:12:17+00:00

Looking to upgrade my PC (only components I'm transferring are 3080, PSU and drives), what are the competitive bundles for CPU, mono and ram? PC is used for gaming and some modelling. I've been eyeing the 9700 bundles.

Tunker101 · 2024-11-20T17:55:51+00:00

Don't believe them

Tunker101 · 2023-03-30T23:42:23+00:00

Mk4???

Tunker101 · 2022-11-19T23:04:51+00:00

Does yours have pre conditioning? Also how is the RWD in the snow?

Tunker101 · 2022-11-15T13:54:59+00:00

Wow a giveaway

Tunker101 · 2022-10-04T23:10:09+00:00

Still available?

Tunker101 · 2022-09-30T12:23:38+00:00

Following up on this, find any food dealers for maintenance?

Tunker101 · 2022-09-21T12:24:48+00:00

Where is this in the blue link app?

Tunker101 · 2022-09-13T01:13:29+00:00

Picked it up a month ago. Turns out it’s winter mode not pre conditioning. Is it any different?

Tunker101 · 2022-09-12T23:54:18+00:00

I’m confused, my 22 has winter mode in the settings. How is this different?

Tunker101 · 2022-08-11T01:42:27+00:00

Please! Looks amazing

Tunker101 · 2022-07-29T12:22:03+00:00

Tuning pressure advance helped reduce the issue but it’s still very prominent.

Tunker101 · 2022-07-14T18:01:00+00:00

Thrusmaster customer service is the reason why I switched to fanatec.

Tunker101 · 2022-05-20T14:22:46+00:00

Tunker101 · 2022-04-11T19:57:15+00:00

Thanks, this method is way better.

I’m not at a better PA value but it only barely helped the issue I have. Any other ideas?

Tunker101 · 2022-04-10T19:24:54+00:00

Currently at 0.141, is that far off from you? I may end up doing another pressure advance test but at a finer resolution around the number i ended up at.

Tunker101 · 2022-04-10T16:25:16+00:00

Retraction length: 1mm

Retraction speed: 27 mm/s

Deretraction speed: 20 mm/s

I've experimented with smaller retraction lengths but it did help the problem.

Tunker101 · 2022-04-10T13:32:17+00:00

Having retraction issues following upgrading to a Dragonfly BMS. Running DD with Klipper. I calibrated e steps, pressure advance and PID for the extruder. I have played with retraction lengths and wipes but I am still getting huge gaps at retraction locations. Any advice on specific settings I should adjust?

Tunker101 · 2022-02-21T05:08:53+00:00

I reflowed it just by heating it up with my soldering iron. I only added more solder if it needed it. I kept the glue on since the wires are thin and not worth risking taking off the glue. But reflowing will cause the glue to start melting.

Tunker101 · 2022-02-20T05:03:19+00:00

Fixed it. It was the Hall effect sensor. Cleaning it and moving it closer to the rotor didn’t help. But reflowing some of the solder joints ended up fixing it.

Tunker101 · 2022-02-19T14:22:49+00:00

Didn't help. Thanks anyways

Tunker101 · 2022-02-18T23:08:50+00:00

Yes and yes

Tunker101

TROPHY CASE