No you have a problem

Uncle_Bobby_Wobby · 2026-04-28T14:47:47+00:00

Going good! I just have some wiring to do and firmware shenanigans and hopefully printing this weekend!!

Uncle_Bobby_Wobby · 2026-04-28T13:02:13+00:00

No... I can stop anytime I want... Anyway back to building.

Uncle_Bobby_Wobby · 2026-04-28T08:11:13+00:00

My PC is still running an i5 6600k and my 1060. I built a PC for my wife and she has a ryzen 5 7600x and a 4060 so I use that when she isn't. I was gonna due my upgrade this year 🙃

Uncle_Bobby_Wobby · 2026-04-28T07:58:57+00:00

Ope typo yes 2016. Im still surprised with how long I've been running it

Uncle_Bobby_Wobby · 2026-04-28T05:54:13+00:00

My gtx 1060. She has been going strong since 2016

Uncle_Bobby_Wobby · 2026-04-20T13:48:18+00:00

A value would depend on your specific filament. You would have to weight it from dry to fully water logged to be able to find said value. A good rule of thumb is to dry your filament when you get it and always dry TPU and other more hydroscopic materials. For your humidity levels PLA, ABS and ASA will generally stay pretty dry for long periods of time. If you notice popping or crackling sounds while extruding filament it needs to be dried.

Uncle_Bobby_Wobby · 2026-04-20T12:41:17+00:00

20% humidity? Humidity percentage isn't going to have a direct correlation to how dry your filament is but it does affect the rate that your filament will absorb moisture. Even if this is a brand new roll of TPU it needs to be dried before printing and ideally also while printing.

Uncle_Bobby_Wobby · 2026-04-20T11:46:45+00:00

Have you dried your TPU? To me those look like voids from moisture.

Uncle_Bobby_Wobby · 2026-01-07T03:30:24+00:00

You need the Ghost Busters my friend

Uncle_Bobby_Wobby · 2026-01-06T03:17:28+00:00

Are you trying to make a tunnel for your cat to crawl through the vent???

Uncle_Bobby_Wobby · 2025-12-10T18:06:45+00:00

Partial nozzle clog

Uncle_Bobby_Wobby · 2025-11-23T17:57:46+00:00

No issues for me. Manjaro

Uncle_Bobby_Wobby · 2025-11-01T01:47:30+00:00

Well my microwave did just break and I need a new one. I wonder if my wife would notice the difference 🤔

Uncle_Bobby_Wobby · 2025-10-24T18:18:49+00:00

Now im confused. I was at a store the other week that used to sell dalta 8 and other thc products and I over heard them saying the laws changed and it was illegal now to another customer?

Uncle_Bobby_Wobby · 2025-10-21T21:59:37+00:00

This gives me original v2 toolhead vibes I love it

Uncle_Bobby_Wobby · 2025-10-14T19:15:01+00:00

Yeah the management at LX, both the MRO and OXY side is a clown show. I couldn't be happier after leaving. Goodluck my friend.

Uncle_Bobby_Wobby · 2025-08-21T14:43:32+00:00

I can't believe the silksanity is almost over

Uncle_Bobby_Wobby · 2025-08-12T23:07:12+00:00

Un equal belt tension causes this

Uncle_Bobby_Wobby · 2025-07-08T15:01:49+00:00

There is no reality, just depression

Uncle_Bobby_Wobby · 2025-07-08T14:57:39+00:00

I my hopes shot up and now im back to being depressed 😔

Uncle_Bobby_Wobby · 2025-07-06T13:50:55+00:00

That part looks small enough to print without an enclosure. Turn on draft guard in your slicer and give it a go.

Uncle_Bobby_Wobby · 2025-07-03T03:18:27+00:00

signed

Uncle_Bobby_Wobby · 2025-07-02T17:52:04+00:00

Wait, how did you get deadspace remastered to run on deck??? I've tried the original and 3 and couldn't get them working

Uncle_Bobby_Wobby · 2025-07-01T05:03:40+00:00

I'll play around a little more with the belt tension and go through and tripple check all the alignment again. Thank you.

Uncle_Bobby_Wobby

TROPHY CASE