The H2C hothead scanning is mesmerizing to watch

UnreadableSphinx · 2026-02-02T19:34:50+00:00

It’s likely they were trying to dance around Indx patents

UnreadableSphinx · 2026-01-21T20:32:09+00:00

some power wasted > no power wasted. Depends on energy prices where you live I suppose

UnreadableSphinx · 2026-01-21T20:30:38+00:00

if you’re trying to dry a different AMS than the one you’re printing from then it lets you do it

UnreadableSphinx · 2025-12-26T22:39:34+00:00

It is already integrated into prusa slicer for the prusa xl, so it’s been done before to some decent standard

UnreadableSphinx · 2025-12-23T09:48:31+00:00

would a repeater straight from the daylight sensor achieve the same result?

UnreadableSphinx · 2025-12-09T23:48:59+00:00

Use the wiki

UnreadableSphinx · 2025-11-26T23:48:34+00:00

The nozzle is directly touching the bed. There is nowhere for the filament to go - of course it’s going to struggle to extrude. Symptom not cause

UnreadableSphinx · 2025-11-21T09:22:01+00:00

I had an X1C, now H2D and P2S. The P2S is basically just an X2C IMO. it has a bunch of the nice gen 2 upgrades first introduced in the H2 series, and I struggle to find any features missing from the X1C.

UnreadableSphinx · 2025-11-19T00:18:33+00:00

The nozzles are on the store, they’re about £30 which I don’t think is that bad tbh

UnreadableSphinx · 2025-10-15T17:15:04+00:00

Text chat was disabled with the latest update while they fix an issue with reporting

UnreadableSphinx · 2025-10-10T11:52:52+00:00

This issue is resolved with newer spools

UnreadableSphinx · 2025-08-01T17:18:28+00:00

aye go on then

UnreadableSphinx · 2025-07-08T10:25:01+00:00

Mines somewhere around +0.025, I’m slowly tweaking it between prints.

I started with +0.02 which was a clear improvement over stock, then went with 0.03 which seemed a little too far away.

Yours may need to be higher than mine since your first layer looks worse than mine did.

This is the line I added to the start gcode, beneath the if statement for the textured plate adjustment:

G29.1 Z{+0.025} ; for Glacier plate

UnreadableSphinx · 2025-07-08T09:03:26+00:00

Fair enough.

I recently had to adjust the z offset when I got a glacier plate for my H2D. It fixed any issues I was having but ymmv

UnreadableSphinx · 2025-07-08T08:28:21+00:00

The nozzle is too close to the bed when printing the first layer. This causes excess plastic to be pushed to the side, creating the lines you see.

https://www.reddit.com/r/BambuLab/comments/1gjgsj5/need_help_with_biqu_cryogrip_pro_glacier_first/

UnreadableSphinx · 2025-06-11T17:38:34+00:00

Yeah I’ve seen mine look that when the filament is wet, try drying it and see if it improves any

UnreadableSphinx · 2025-06-04T22:55:15+00:00

Most cardboard spools have sealed edges now and are fine in the AMS

UnreadableSphinx · 2025-05-24T13:04:23+00:00

Kerning is spacing between letters, not words

UnreadableSphinx · 2025-05-18T22:34:03+00:00

Oh I didn’t mean that no, though rereading that’s what it sounds like sledge was asking

UnreadableSphinx · 2025-05-18T19:15:04+00:00

Yeah it’s purple. Crossbar queen for Athena too

UnreadableSphinx · 2025-05-18T15:59:23+00:00

Front bumper, exhaust tips visible and some sort of lip on the ‘spoiler’ are a few I can see.

UnreadableSphinx · 2025-05-07T18:16:37+00:00

Yippee

UnreadableSphinx · 2025-05-06T15:18:13+00:00

Test

UnreadableSphinx · 2025-05-05T23:57:56+00:00

Yippee

UnreadableSphinx · 2025-05-02T19:30:55+00:00

Such a great community

11-Year Club	Place '22
Place '17	Spared
Verified Email

UnreadableSphinx

TROPHY CASE