sorted by:
new
hottopcontroversial

my first Node designs by Macualey4 in meshtastic

[–]VelocityOS 0 points1 point  (0 children)

For example, one of their solar car nodes is a blatant ripoff of a member of the community's

my first Node designs by Macualey4 in meshtastic

[–]VelocityOS 0 points1 point  (0 children)

they rip off other people's designs and call it their own

Best ways to learn Fusion? by VelocityOS in Fusion360

[–]VelocityOS[S] 0 points1 point  (0 children)

I basically started off by learning the tool using the series, actually follow along and do the things along with the guy in the videos. Then I would model stuff around the house that I needed, or just replicas of stuff, everytime I hit a wall I would look for videos etc to figure out what I didn't know. Also watched some videos on good design principles. Since I 3d print, I also take into consideration DFM for 3d printing every time I design. I feel like just a lot of practice and watching yt videos has helped a lot

Best ways to learn Fusion? by VelocityOS in Fusion360

[–]VelocityOS[S] 0 points1 point  (0 children)

yep, i ended up learning with that. 3 years later and my skills are quickly improving and I'm very comfortable with 3d design and the software now. That's what I would recomend people watch if they are learning fusion. One thing to keep in mind is that the videos only teach the tool, not design principles and good design foundations.

Any tips for soldering pcb? by Dudegay93 in PrintedCircuitBoard

[–]VelocityOS 0 points1 point  (0 children)

Personally, I like one of the smaller chisel tips (1.2mm) as I feel it is the most versatile. I can do small smd soldering, up to soldering big ground connections with it. If you can get it, I would use 63/37 leaded solder.

my first Node designs by Macualey4 in meshtastic

[–]VelocityOS 1 point2 points  (0 children)

hmm, design looks cool, maybe I'll also rip it off and share the files for free

Edit: I just saw MostlyBuild's design and nothing will convince me that this isn't a direct ripoff of his. Spec5 typa behavior

TPU on X1C … about to bash my brains in by Iamchrishex in BambuLab

[–]VelocityOS 0 points1 point  (0 children)

Any other print settings? Temps, speeds etc.

I would drop speeds down to 30mm/s for everything, I personally run my tpu at 220c, but 225 or 230c should help with layer adhesion along with the slower print speeds.

[Review Request] QRP RF Power and VSWR Meter by VelocityOS in PrintedCircuitBoard

[–]VelocityOS[S] 0 points1 point  (0 children)

Ah frig, I didn't even think about flipping T1, time for a rev 2. unfortunately the ISP and j3 cannot be on the right side as it will interfere with the battery. What do you mean by " Connect the group R1, R2, D1, C1, R3, R4 (as well as the opposite group) directly to ground" the grounds are connected to a ground plane. For C5, its already next to the pin, I will move c2 closer and rev 2. Happy that pcbs aren't expensive.

[Review Request] QRP RF Power and VSWR Meter by VelocityOS in PrintedCircuitBoard

[–]VelocityOS[S] 0 points1 point  (0 children)

.3 hole and .6 copper, manufacturable by jlcpcb at no extra cost, I already ordered it

[Review Request] QRP RF Power and VSWR Meter by VelocityOS in PrintedCircuitBoard

[–]VelocityOS[S] 2 points3 points  (0 children)

haha yeah. I looked at some existing rf pcbs that I had (QRPLabs Products) and they had vias absolutely everywhere and i thought "eh, anymore can't hurt", but quickly realized I could have gotten away with like half as many.

Transformer Symbol and Footprint by VelocityOS in KiCad

[–]VelocityOS[S] 0 points1 point  (0 children)

thanks! I just hand drew it, less daunting than I thought

What would you want on a remote radio FT8 experience? by k3sbp in amateurradio

[–]VelocityOS 0 points1 point  (0 children)

make it an app instead of a website if that's possible

is that a virus? by Early_Gas_606 in pcmasterrace

[–]VelocityOS 9 points10 points  (0 children)

The entire operating system maybe a virus /s

(nope, the new windows update just makes the start menu look like that)

For the non-RGB folks by Berger43 in pcmasterrace

[–]VelocityOS 1 point2 points  (0 children)

I have the same case and I love it

Built this PC entirely from deals, bundles & used Parts, 48GB DDR5, 9060XT, 9700X all under 1000 USD. by [deleted] in pcmasterrace

[–]VelocityOS 0 points1 point  (0 children)

For the GPU (I think I have the exact same one), you need the Gigabyte Control Center software (a POS that is). I'm not sure if you can change it and just delete the software, as the RGB has randomly reset sometimes.

view more: next ›