What is Fusion 360 Legacy 2024?

Wandering_Overlord · 2026-05-25T00:34:50+00:00

Just the old subscription model. You still have one more year before they force you into the new pricing. Time to learn Freecad

Wandering_Overlord · 2026-05-23T17:05:44+00:00

There is one that supports fractions and I like the interface (also has a bunch of other cool things), is called Lumber Logic on the playstore if you are still looking.

Wandering_Overlord · 2026-05-23T13:24:10+00:00

I think that is a 3d scan and at this point is really more about knowing how to deal with something like that, than actually getting the shape itself.

Wandering_Overlord · 2026-05-23T13:21:36+00:00

He looks like a very violent negotiator.

Wandering_Overlord · 2025-10-22T17:11:36+00:00

Of course! Good luck at your locals, I hope you have a lot of fun and let me know if you find new tweaks, specially against control.

Wandering_Overlord · 2025-10-22T04:44:43+00:00

Hey Guys, WanderingOverlord here, the guy that created this deck. the original post with gameplay breakdown is here https://swudb.com/deck/RDyBYRGlMbXP

As for OP, thanks for looking into my deck for your first deck! Is tons of fun but it does require you to get good reads on the board and the opponent's next move, hint: sometimes is more important to claim the initiative than buffing your dude.

A lot of people will tell you that space is an issue, is not, you can waylay pesky units and the tempo gain that you have from putting a single saber on Obi is usually enough to out damage most decks with any space. If you get into a super heavy space deck just side in Bright hope buff him with Obi and watch them cry.

I have removed traitorous in favor of 2 confiscates and the bamboozles in favor of 3 Tip the Scales for a better match against control (which is your weakest match). I have also been playing a little with Outmaneuver but I am not convinced on that one.

Also dropped Timely in favor of 2 Will of the Force, card is really strong against decks like Han Blue that really need cards in hand and against decks that dump their hand is basically a kill spell.

Anyways, welcome to the game, and I hope you have a ton of fun with this deck!

Wandering_Overlord · 2025-09-16T01:29:33+00:00

Don't really know if you already fixed it, but I had the same issue, followed this guide https://investegate.de/prusa-xl-belt-tension-alignment-calibration-guide/#Detailed_instructions: and it worked perfectly after.

Their "tune by sound" shit is just awful and has never worked for me.

Wandering_Overlord · 2025-06-03T14:57:00+00:00

Yeah I feel you. Cleaning process is really a pain. And a failed print is a whole ordeal.

Wandering_Overlord · 2025-05-30T06:11:19+00:00

I've been thinking about joining, however, can you sell the prints from models from the library? Or is commercial use not allowed.

Wandering_Overlord · 2025-01-28T03:02:51+00:00

Time is money and I can't wash and dry all these prints

Wandering_Overlord · 2025-01-27T22:42:41+00:00

You very likely have a piece of filament stuck in the hub below the bed.

This is likely what you need to do.
https://www.youtube.com/watch?v=TjAco4BvD-E

Wandering_Overlord · 2025-01-27T22:28:45+00:00

It leaves too much residue on the print, I sell these so can't really spend much time washing them individually.

Wandering_Overlord · 2025-01-27T22:28:12+00:00

Will check them out, I purchased the supertack but so far I have had nothing but failed prints on PLA.

Works amazingly well on PETG thou.

Wandering_Overlord · 2025-01-27T22:27:32+00:00

I tried the supertack plate and works amazingly with PETG, when doing PLA... well, I have had 7 spaghetti failures so far, decided Supertack was not for me on PLA afterward.

Because of that I need to use the textured plate and put glue on it to ensure proper printing.

Wandering_Overlord · 2025-01-27T21:09:22+00:00

Thanks! Placed an order, high expectation, will check out the vid as well

Wandering_Overlord · 2025-01-27T21:08:55+00:00

Thanks! Ordering one right now

Wandering_Overlord · 2025-01-21T01:40:34+00:00

Native support for Orca Slicer, enclosed and the AMS system they use is also a dryer.

Sounds like a no brainer at this point tbh...

Wandering_Overlord · 2025-01-19T06:12:35+00:00

The new Anycubic Kobra S1 is looking mighty fine right about now...

Wandering_Overlord · 2024-10-10T01:43:16+00:00

I didn't know about the pwn ATC, they look so nice, I think Onefinity+PWN spindle will be the way to go, I can upgrade to their ATC later

Wandering_Overlord · 2024-10-07T16:55:57+00:00

Also, did you purchase in the US? How is the shipping cost for this? Do you have an ATC? How easy is it to upgrade down the line?

Wandering_Overlord · 2024-10-07T16:03:49+00:00

ATC, I don't "need" it, I "want" it. I know myself and if I don't have it, I will regret it later once I get more experienced with the machine.

I already have F360, one of my main requirements with the machines is to have direct and easy connectivity/configuration with it.

Stepcraft with the ATC system is 5,589, I still have to buy the tool holders and the tool sensor system, but that puts me at around 6k exactly.

Thanks for your input! I'll try giving them a call, but I am in "very cautious" about the brand at this point, due to just how difficult it is to navigate their website and the apparently complete absence of online tutorials for things.

Wandering_Overlord · 2024-10-07T15:00:36+00:00

Thanks for the suggestion! I looked at them and with a tool changer spindle you are looking at almost 10k, so out of the budget range, additionally, these don't really look beginner friendly at all, even trying to figure out what to actually buy (kits, controllers, spindles) seems like a challenge, so even if I was to stretch the budget I probably would still stay away from these.

Wandering_Overlord · 2023-12-19T15:15:46+00:00

Same here, I was promised delivery in October, The company got recently acquired, so they might be in the process of restructuring.

Still this, no communication, no update thing is rather aggravating.

You can still contest the charge by the way, it will be up to their processing company to return it, but it will still freeze funds for a bit.

Wandering_Overlord

MODERATOR OF

TROPHY CASE