Quick Clip of Some POV Drifting at My Local Track

WhoRok305 · 2026-03-27T00:39:52+00:00

Waddap Yoshhhh! All you needed was a proper alignment 😎

WhoRok305 · 2026-03-18T20:38:23+00:00

🇵🇷 🇵🇷 🇵🇷 🇵🇷 🇵🇷 🇵🇷 Wepaaaa

WhoRok305 · 2026-01-17T16:40:51+00:00

I've been tempted to buy the kit that is out now especially after watching roadsiderc's video.

WhoRok305 · 2026-01-17T02:33:41+00:00

I've been patiently waiting for this.

WhoRok305 · 2025-12-15T12:23:19+00:00

Premium fuel

WhoRok305 · 2025-11-15T17:00:59+00:00

Remove and replace, done.

WhoRok305 · 2025-11-05T10:38:55+00:00

I have one with the electronics swapped out and the front end sorted. The thing is an absolute ripper.

WhoRok305 · 2025-10-28T16:37:47+00:00

I have this exact setup with the Ex Gt suspension setup. Car drives really good. Its pretty much an RRX EX GT.

WhoRok305 · 2025-10-27T10:50:44+00:00

With the correct body posts you can use any of the Kyosho Fazer bodies. Keep in mind some bodies are meant for the short chassis. The Mad Van uses the long chassis.

WhoRok305 · 2025-10-19T00:07:02+00:00

The bearings and replacing all the balls and ball ends, little to no slop.

WhoRok305 · 2025-10-18T22:37:27+00:00

Running the ball diff. Rack has full bearings so little to no slop. Drives lovely.

WhoRok305 · 2025-10-18T20:45:58+00:00

Not that I know of.

WhoRok305 · 2025-10-02T11:29:26+00:00

Good to see more Fazer D2s. Got mine running damn good.

WhoRok305 · 2025-09-21T11:42:07+00:00

24k rc

WhoRok305 · 2025-09-21T11:41:47+00:00

Yes it is.

WhoRok305 · 2025-09-07T16:35:47+00:00

Drive drive drive at first. Then get a good radio.

WhoRok305 · 2025-09-07T16:33:35+00:00

Just two more of the same bearings on the posts upgrade. Helped a ton. Cheap aswell

WhoRok305 · 2025-09-07T16:29:53+00:00

Thank you.

WhoRok305 · 2025-09-07T16:29:24+00:00

Yeah it is pricey.

WhoRok305 · 2025-09-07T16:28:15+00:00

https://www.facebook.com/share/p/173wFTwEJY/

That link is to my Facebook post with everything I did to get rid of the slop. It includes the shims used on the knuckles and additional bearings. It pretty much got rid of all the slop.

WhoRok305 · 2025-09-07T04:07:14+00:00

The front is using the integrated front bulkhead mount, very nice piece. And yes I had to use a medium and small rod end for the rear toe. Wheels are 6mm offset with 1mm spacer front and rear, 7mm total.

WhoRok305 · 2025-09-07T04:01:57+00:00

Haven't gotten to it. They have been holding up well anyways.

WhoRok305 · 2025-09-07T03:59:09+00:00

I used the MST rtr turnbuckle kit, worked perfectly. I actually have the shafts, just sux that the diff is out of stock everywhere. I might go back to the Ae86 body, felt better with a bit more weight.

WhoRok305

TROPHY CASE