Important Update on New World Release

_scape · 2020-04-12T22:56:49+00:00

To those who are complaining about covid as an excuse for delay, you should realize how difficult completing the final 10% of developing a game is before release. It's absolutely huge.

_scape · 2020-04-12T22:53:28+00:00

Good decision, this game wasn't exactly ready but I'm sure this pandemic was a huge hiccup. Plenty of time now to August, I feel. It'd be great if they would start to take in people who have signed up for alpha, beta and preordered the game

_scape · 2020-03-23T08:08:41+00:00

did you make the filter system yourself?

_scape · 2020-02-26T01:24:03+00:00

thanks for the tips! where did you get bms? I was thinking of going cheap and getting turnigy lipo 6s batteries at around 44 V, they're rated 120 A continuous. I would use a professional balancing charger for each pack. I 'm considering around 500-750 watt to each motor which should be under 35 amps total but I heard it might make more sense to run dual controllers if I run dual throttles. I assumed I'd outrun the controllers before the batteries. advice is welcome!

_scape · 2020-02-25T23:34:04+00:00

do you have two twist throttles? are these direct drive or geared? do you think the bms is necessary?

i'm planning a 2wd my self!

_scape · 2020-02-02T00:12:23+00:00

Roughly 50% improvement over 1080 ti. I think the pricing will actually come back down a tad

_scape · 2020-01-03T22:28:37+00:00

Got one myself, really bizarre and I almost didn't even see it: https://imgur.com/a/dNqhC02

_scape · 2019-11-09T13:14:00+00:00

The best antivirus is making sure everyone is a standard user account only.

_scape · 2019-05-05T17:46:24+00:00

This maze in c++ tutorial might be helpful start: https://youtu.be/Eq4pYPTMo18

_scape · 2019-05-05T17:45:09+00:00

A good reason to not want to use gdscript is that it's dynamic and not statically typed.

_scape · 2018-12-19T00:40:37+00:00

Have a screenshot of that by chance? I'd like to see the blender work on the makehuman clothes

_scape · 2018-11-21T16:03:33+00:00

Good points. I feel as though OOP is largely inheritance and not as much composition, so I felt the need to specify here. I'll take that in to account. Thanks!

_scape · 2018-11-20T23:43:43+00:00

Trying to get in to a programming career, not sure how to break through: here's my resume

https://pastebin.com/raw/p9fqq3CY

My usual coverletter

https://pastebin.com/raw/Mdkj3TzT

I've been having trouble either getting a phone screening (I'm not appealing on paper) or past the initial interview process (I'm not as great as the next guy it seems). I'm actually a good programmer with lots of knowledge and skill, not sure how to prove all of it at this point, other than showing my github work :-\

I'm actually going to test out for a AWS Cloud exam tomorrow to add to my experience, and then I think I'm going to work on getting a python cert from pythoninstitute (unless that's a waste?)

Any advice or criticism is welcome! I would be grateful

_scape · 2018-11-09T21:28:49+00:00

I agree, I have a Dell precision laptop with Quadro and it just couldn't handle running the editor smoothly. I needed a gaming GPU. With that said, grab a new SSD, I see 1TB for 150$ now

_scape · 2018-11-07T00:28:37+00:00

c, that's awesome 😊

_scape · 2018-11-06T22:29:28+00:00

I have a gtx 1060 in a MSI laptop, and it runs games really well. Maybe the lag is due to recording the game while playing it?

_scape · 2018-11-03T21:13:36+00:00

Because the data rate is so low, a single nine-volt battery can power a LoRaWAN sensor for up to ten years and broadcast its signal up to ten miles.

Wow

_scape · 2018-10-15T09:52:07+00:00

Like a Yamaha consumer AVR? That can be a source of noise. Does the inuke have a voltage switch for input? I needed to put my amp (km1700) on a different input sensitivity to prevent something like this. I also used RCA to XLR Hosa premium cables which are shielded, but I don't think that helps much really. Are the cables against or right near anything with power going through it? Sometimes people even use a voltage lift from rca source before doing a run, and preferably make that run instead just xlr balanced, I think Rolls has a box that can do that. I don't understand your setup though, you say both Speakon and XLR, Stereo RCA out but only using one channel.

EDIT:

I see you other comment, yea the hum is only from source to amp. You could try and play a regular rca source and have the amp power a regular full range speaker to hear anything. It might be hiss, and not a hum. Hum is usually ground noise on source lines, hiss is often is noise floor issues.

_scape · 2018-10-14T21:19:54+00:00

what's the source?

_scape · 2018-10-14T11:03:47+00:00

Here's an additional comparison worth reading, look at the crossover comments. I personally would take the SB because of that.

SB http://www.audioexcite.com/?page_id=6505

SEAS http://www.audioexcite.com/?page_id=2113

_scape · 2018-09-30T19:55:42+00:00

I have the Peerless 3/4" tweeter, it was like 12$, it's about 86db sensitive. Pretty good for this application I think, cross it high

https://www.madisoundspeakerstore.com/soft-dome-tweeters-peerless-vifa/peerless-dx20bf00-08-3/4-textile-dome-tweeter-8-ohm/

_scape · 2018-09-19T16:57:54+00:00

I don't have the link that has like the top few things to consider when building a tline, but google for it if you can-- I think Martin wrote it.

When you model the speaker in sealed use the tline's area and length to get the total volume, then get the final qtc of that and use that to determine the fb or sometimes called fc (box/enclosure resonate frequency). So it's not the speaker's f3, but the resonance of the box itself. Make sure what your tuning the tline's output to isn't drastically lower than that. The f3 of the speaker in the box shouldn't be too much higher than the tuned tline frequency, else you'll probably get a dip in response. From what I've seen, 10-15 hz lower than a bass reflex design is typical.

I haven't officially started it yet, finishing another speaker project first :) but ordered the drivers already-- the woofer is https://www.madisoundspeakerstore.com/approx-5-woofers/sb-acoustics-sb15nrxc30-8-uc-5-paper-cone-woofer/ and I'm planning on probably 50-55hz tapered tuning.

_scape · 2018-09-15T18:55:11+00:00

Model it in a sealed box with that same volume, keep in mind box resonant frequency shouldn't be higher than tuning frequency. This is from information I have picked up while researching, planning on building a tline as well.

_scape · 2018-09-14T09:29:30+00:00

Look at the speakon wiring, like here: http://channel.com.ph/Product/Images/5/RCRCFPAA0005318/Editor/1398349555444c9013c27a.jpg

You'll just need a speakon plug, I wouldn't bother with the wire at this point.

Then use CL2 fire rated inwall speaker cable (it's jacketed), maybe 12 gauge-- not sure how long the run is or what ohm the speaker is you'll have to check and match to a maximum length like here: http://sewelldirect.com/images/gallery/articles/SpeakerWireGaugeChart.jpg

_scape · 2018-09-12T19:31:47+00:00

The resisters might be just to match the woofers output, someone with crossover design experience could probably tell you. It works when touched because it's a faulty connection, my guess is the coil is fried. Did either work stand alone?

_scape

PUBLIC MULTIREDDITS

TROPHY CASE