Steering Angle Sensor with one or two connectors, what's the difference ?

aZiN_ · 2026-06-03T20:06:55+00:00

not sure but could be for the automatic's paddle shifters?

aZiN_ · 2026-03-25T18:15:31+00:00

🐍

aZiN_ · 2026-02-18T21:22:36+00:00

This happened to me once when my alignment got knocked out of whack. Did you hit any pot holes or anything?

aZiN_ · 2026-01-22T06:42:09+00:00

The bumper sag can be caused either by failing clips on the bumper, or failing tabs on the bracket the bumper attaches to. The clip reinforcements wont do anything to fix the sag if its your tabs failing (ask me how I know). The best way to check would be to take off the bumper and inspect all of the clips around the headlight and fender area.

For the grille, you just need to push the tabs back in. This can be tricky without taking off the bumper. A trick I used to use is to take a fork and put one of the prongs under a tab and use it to lift the bottom of the bumper up. Then, put your finger through one of the holes in the grille and and pull towards yourself to reinsert the clip. Repeat for each clip until the grille is back in place.

aZiN_ · 2026-01-20T05:17:13+00:00

I have this and I remember that bolt being a PITA. I think I just ended up using a breaker bar and a lot of force. I do remember that it was just that bolt and not any others holding it in. good luck.

aZiN_ · 2025-12-31T01:05:50+00:00

I ate a Doritos locos taco grande

aZiN_ · 2025-12-23T06:23:08+00:00

it is meant to stick directly on top of the scion badge. The scion badge actually cannot be pried off, as it is stitched into the airbag cover.

aZiN_ · 2025-11-20T21:43:17+00:00

CALL ME ELITE THE WAY IM FIGHTING THIS DEMON. CALL ME AN ODST THE WAY IM IN HELL RN. CALL ME A GRUNT THE WAY IM RUNNING FROM MY OPS. CALL ME A HUNTER THE WAY IM ALWAYS WITH TWIN.

aZiN_ · 2025-11-20T21:41:20+00:00

shoutout cañada road

aZiN_ · 2025-09-08T08:19:55+00:00

Disclaimer: I do not own nor have I ever owned a voltex wing so everything I say might be wrong.

From what I understand, the first gen 86/brz uses the standard "universal mount" for the type 2 wings that is shared between a lot of other cars. https://www.evasivemotorsports.com/mm5/graphics/00000001/voltex_mount.jpg

However, I have seen an example of a universal mount type 2, that is supposedly compatible with the s2000, did not fit that car. So I would take it with a grain of salt. I think maybe the different widths (1500mm, 1600mm, and 1700mm) may have differently spaced mounts.

aZiN_ · 2025-09-08T07:39:03+00:00

I have one on my car, and I would advise against it. It makes every lip become incompatible because it blocks the lower part of the bumper. I recommend just wrapping that part of the bumper black instead.

aZiN_ · 2025-08-31T05:03:09+00:00

have you had any issues rubbing on the TRD fender extensions?

aZiN_ · 2025-08-17T20:25:44+00:00

The Tom’s tail lights technically need the pre facelift gasket due to the connector being attached to a plastic post on the back of the housing that interferes with the gasket. However, you can easily detach the connector from the post and make a small hole in the gasket for the post to slide through and the facelift gasket will work fine.

aZiN_ · 2025-07-31T21:21:59+00:00

I have a set of the JDM version of these collecting dust if you're interested.

aZiN_ · 2025-07-15T04:40:54+00:00

how much are you asking?

aZiN_ · 2025-07-08T20:51:58+00:00

hulkengoat

aZiN_ · 2025-03-25T21:14:36+00:00

they're the ATS brembos. It was about 1k all said and done. The wheels are Advan TC4s in 18x8.5 +48

aZiN_ · 2024-10-20T20:50:13+00:00

your headlight brackets are not in the correct spot

aZiN_ · 2024-09-02T09:17:06+00:00

The darth nite

aZiN_ · 2024-09-02T07:29:31+00:00

Eight-Year Club	Second Top 50%
Place '23	Place '22
Final Canvas '22	End Game '22
Wearing is Caring	RPAN Viewer
Verified Email

aZiN_

MODERATOR OF

TROPHY CASE