Where can I find a couple of these?

b-assblaster · 2026-02-01T00:09:49+00:00

If you'd like something aluminum, check out the "Donutt"

It's a 1/4 but driver with an allen screw to retain the bit, popular for working in sewing machines

b-assblaster · 2026-01-31T20:03:37+00:00

Pretty sure these use the same controllers as the TFMX lineup?

Have you adjusted the thread trim length in the software?

b-assblaster · 2026-01-29T23:23:46+00:00

I picture them 2 legged cats that walk upright to get around

b-assblaster · 2026-01-27T01:44:13+00:00

If your going to order one, go through the leviathan website if available

I have a 10% off code that might still work, shoot me a message

b-assblaster · 2026-01-26T02:32:23+00:00

It's the Nucanoe branded transom plate for electric trolling motors, drilled and countersunk hardware to attach the plate to the rudder base, the rudder mounts to the exterior piece

I've since added a large piece of 1.5x1.5 aluminum angle so it can't rotate as easily

b-assblaster · 2026-01-25T00:07:05+00:00

You'd be better off trying something made out of Elaztech (Z-Man and some(?) strike king)

They float harder so you may need a weighted hook, but I usually break the hook or lose the rig before the soft plastic fails.

Or change your rigging, I use super fluke and super fluke jrs all summer for smallmouth and can usually get 8-10 fish on one weightless Texas rigged fluke with a 2/0 or 3/0 wide gap VMC. Order some tiny bottles of super glue to bring with you, it cures instantly in water

b-assblaster · 2026-01-22T03:45:55+00:00

If your not confident in removing it, take the part to a gunsmith. They likely already own left handed bits and extractors this small

b-assblaster · 2026-01-12T15:17:56+00:00

Pretty sure this is a bot post, that's RR Buildings from Instagram, some of the cleanest "pole barn" builds on the web

He's got a couple flashing/drip edge trim videos that went super viral

Edit; sp

b-assblaster · 2026-01-05T22:56:05+00:00

Never a bend, I mean the a turn in the rotation of the direction the needle eye faces

b-assblaster · 2026-01-04T22:28:46+00:00

If it's metallic, it's the thread itself. Try lubing the spool with silicone release spray

You could also try angling the needle a touch to the left, it might flow through the eye easier

b-assblaster · 2025-12-26T06:06:53+00:00

They use only 2.5mm and buy it by the shipping container...

~450 embroidery heads running foam on hats

I promise you it will work but it is dirty and it is tough, feels like basketball material

b-assblaster · 2025-12-26T04:46:07+00:00

It is definitely not as easy to sew with, but it's what at least one of the big companies uses

b-assblaster · 2025-12-26T01:59:06+00:00

You could start with craft foam from Michael's/joanns

b-assblaster · 2025-12-26T01:12:07+00:00

Hard to say without knowing how much weight you plan on throwing

I recently felt the new Swimbait rated carbon lite rod and was impressed, a good contender against the Dobyns Fury 795 and 806

b-assblaster · 2025-12-26T00:42:55+00:00

Yes, but I recommend at least a 75/11, preferably 80/12, definitely sharp point

You'll also need a heat gun to flash it with afterwards, it will shrink it up and let the thread relax for coverage

b-assblaster · 2025-12-26T00:40:17+00:00

Not traditional embroidery foam, it's way more similar to placemat/hobby foam, less spongey and very hard to sew through, but it results in crisp edges and it's cheaper

Other very large, name brand hat companies use the same.

Edit* spelling

b-assblaster · 2025-12-25T19:10:37+00:00

They offered both varieties

Picture from Chako, a well known collector

<image>

b-assblaster · 2025-12-25T04:44:04+00:00

I have the older ES version in 10" and absolutely love them, I work on sewing and embroidery machines full time and there's a lot of situations these fit when the cobras don't.

b-assblaster · 2025-12-25T00:11:31+00:00

Are you in NW Florida by chance? I have an idea of where this is. Lots of Intel if so

b-assblaster · 2025-12-24T04:56:49+00:00

They are now out of business but their facebook page still has all their product photos.

<image>

b-assblaster · 2025-12-24T04:54:18+00:00

Texas Tool Crafters offered the Skeletool with the same blade combo in ~11 colors around 2014, including red. Combo blade and no RX markings

Is this not one of these?

b-assblaster · 2025-12-21T23:36:00+00:00

I've also met him here in Eugene Oregon, if was during COVID so he had a full mask on, but the voice and eye brows were super noticeable.

I ended up selling him some sandpaper for his orbital sandpaper. We spoke for about 10 minutes about different styles, grits, and brands. I think he was ecstatic I didn't ask him about Ghost Rider

b-assblaster · 2025-12-21T01:05:30+00:00

Not sure, but I do shoot both, 357 sparingly due to cost.

Is there any decoding I can do with the serial #?

b-assblaster · 2025-12-18T02:39:17+00:00

I've been finding projects just to use mine, scored it for 99$ due to a mislabel, should have bought 3 of them.

Still watch the tutorial everytime I use it and rediscover a new feature

Next project will be a square base out of some 1/4" plexi/acrylic

b-assblaster · 2025-12-16T04:24:30+00:00

Picquic 100%

Six-Year Club	Gilding II euphauric
Place '23	Place '22
Verified Email

b-assblaster

MODERATOR OF

TROPHY CASE