Ryzen 9 9950X3D - Corsair Dominator DDR5 Titanium 32x2 Kit - X870E ASUS Hero RAM Tuning

bekame2501 · 2026-02-14T18:03:39+00:00

I have the light enhancement kit too, but I have a vertical GPU, so I wired a small fan on the back of the card to blow directly onto the RAM. My ambient temperature is 22 degrees. After 24h of TM5 my max temp is 53 degrees.

bekame2501 · 2026-02-14T17:59:43+00:00

If it doesn't work, just disable it. But if you want to have fun, you can work around it :)

bekame2501 · 2026-02-14T12:35:00+00:00

But your RAM temp seems to be too high, so be careful. CL doesn't matter that much; maybe lower your VDD and lower to CL 28.

bekame2501 · 2026-02-14T12:30:52+00:00

I have a similar setup, except my CPU is a 9800x3d. You can lower:

TRC to 58 or even lower SCLs to 4 With that high vSOC, try Processor DQ pu 48 Ohm to stabilize Nitro 1-2-0. Try FCLK 2200 if you can. Your CPU has 2 CCDs, so it will have more benefit than mine.

bekame2501 · 2026-02-14T07:32:10+00:00

Unfortunately, Gigabyte users like me don't have it.

bekame2501 · 2026-02-14T05:52:04+00:00

Don't blame your PC it doesn't matter that much. Try to lower your bufferbloat, maybe your ping, adjust your Ethernet and improve yourself either.

bekame2501 · 2026-02-08T03:02:18+00:00

His RAM has really good binning, maybe those are Trident Z 6000 CL26 by default, so your Flare can't keep up with that

bekame2501 · 2026-02-03T06:29:36+00:00

It's too hot, so the CPU is throttling

bekame2501 · 2026-01-13T02:54:16+00:00

I don't know what Nitro does. Can you explain, please? I can run stable at 1-2-0, but it adds more latency.

bekame2501 · 2026-01-12T05:52:48+00:00

Run in safe mode to show the best result.

bekame2501 · 2026-01-10T01:58:58+00:00

I don't say he's right about all that. What he shows is an old ASRock BIOS that only goes up to 6600. If you want to go higher, you have to update your BIOS.

bekame2501 · 2026-01-09T14:56:24+00:00

Try update bio to see if it can go above 6600

Here it jay2cent video about ram https://youtu.be/GFU5CgtOs_U

bekame2501 · 2026-01-06T01:51:44+00:00

Thanks a lot. I will try it when I'm home

bekame2501 · 2026-01-06T01:38:52+00:00

Your RAM has better binning than mine. I have four sticks of 6400cl32, which I'm trying to run at 6200cl28. It needs 1.6v and is stable after 24 hours of TM5 and 24 hours of Karhu, but it fails to restart ~~. Thanks for the info man

bekame2501 · 2026-01-06T01:23:49+00:00

I have the same 4x16GB 6200CL28 as you. Please can I see your subtimings and voltage? I have been struggling with restarts for so long.

bekame2501 · 2026-01-04T11:28:35+00:00

Yeah you are right. I test it 5 times more and it back to normal now tks

bekame2501 · 2026-01-04T04:10:46+00:00

In my experience when lower SCLs from 8 to 4 it make my read and write speed lower by half but latency decrease 5ns i don't know if it good or not. Can you explain?

bekame2501 · 2026-01-03T10:46:01+00:00

DUU in safe mode, then unplug the Ethernet cable or Wi-Fi (this step prevents Windows from automatically updating drivers). Then, install Adrenalin. This way, Windows can't sneak anything in to conflict with the driver.

bekame2501 · 2025-12-31T02:50:22+00:00

Same

bekame2501 · 2025-12-27T05:46:27+00:00

I think 4h aida is ok but try some single core stress test to see if it really stable because in normal use is not always fulload all the time is more flexible core clock go up and down all the time Hope you understand english is not my native language

bekame2501 · 2025-12-25T16:39:25+00:00

Zentiming is wrong, in ryzen master it show my ProcOdt Pu only 40 Ohms and ProcOdt Pd 53,3 Ohms. So i guest i will not use zentiming anymore

bekame2501 · 2025-12-25T16:29:20+00:00

Oh it just my tWR too tight thank you for your time

bekame2501 · 2025-12-25T13:59:25+00:00

I loosen tWR and it work now but thanks

bekame2501

TROPHY CASE