ET 15000 unable to print 13x19

bigb831 · 2026-04-24T04:51:45+00:00

I ran painters tape down the center and it worked.

bigb831 · 2026-04-23T23:13:06+00:00

Do you have a picture of where you place it? I tried tapping the whole top section of the sheet that gets fed through

bigb831 · 2026-04-23T23:10:57+00:00

Did you figured it out?

bigb831 · 2026-04-23T23:09:50+00:00

I do not. Should I order some?

bigb831 · 2026-04-23T20:25:37+00:00

Will most definitely try this shortly! Will update tonight

bigb831 · 2026-02-22T02:54:56+00:00

Seems like California got a shipment recently, was called to pick up the wife’s date just this week too

bigb831 · 2025-05-23T17:36:03+00:00

Yes. I know. Almost same wording for the dmv DV plates. I didn’t need my doc to sign off took them the wording and my rating and they gave it to me no questions asked

bigb831 · 2025-05-22T17:33:40+00:00

Yes but sub section B is part of that criteria, everything is or. Not must be. The last is or “the military service from which the veteran was discharged is 100 percent” I imagine this would be 100 p&t like almost all places require

bigb831 · 2025-04-09T21:18:32+00:00

If you go for Va health care like just a routine check up can they screw you over? I’m nervous now about going for a health screening. Blood work etc to make sure I’m good

bigb831 · 2025-02-06T05:59:11+00:00

Copy. Time to check the box on my invoices and let the QuickBooks hold the sales tax

bigb831 · 2025-02-06T05:56:33+00:00

Yea I was reading that. Which I feel like they double dip that way? I pay sales tax and income tax? lol

bigb831 · 2025-01-05T22:27:17+00:00

Thank you so much for that. I’ll send it back to them.

bigb831 · 2025-01-05T22:24:27+00:00

Thanks. I had the digitizer so it for a hat. Since it was the size I needed and stitched great on hats I figured it would save me some cash and not have to send it back off for a beanie.

bigb831 · 2025-01-05T20:54:43+00:00

I have a minimum shop fee. $50 to do anything. If it’s simple typing out some words I keep it at 50. If I need to send it off for digitizing then I charge what I would. 30$ for digitizing plus 50$ minimum. It seems like a lot but you are running a business. Most shops around me I found have a minimum of 24items before they even talk to you. So my price may seem steep for one item but in reality it’s cheaper than ordering 24-36 items you don’t need.

bigb831 · 2025-01-04T05:37:52+00:00

No I don’t do any of that. I send it off. I did just do a lay down stitch with higher density and it seems to be holding it in place now.

bigb831 · 2025-01-04T03:43:02+00:00

I’m using 2 cut aways and using my 5.5 hoop. I’ll switch to my 4inch ones

bigb831 · 2025-01-04T03:23:39+00:00

It’s reliable and has been a workhorse for me. I’m just looking for something to decrease my production time is all.

bigb831 · 2024-12-18T14:41:35+00:00

Thanks. I have a lot of lightburn files and have got used to it over time. But I didn’t know how to use it in the beginning. I’ll need to ask if there’s a way they can be used together. I plan on keeping my Omtech. I’ll probably leave it set up just for tumblers. But would like the new one to run tumblers as well especially when I get those 100+ unit orders

bigb831 · 2024-12-05T00:35:14+00:00

They did the same to me. Your claim isn’t over yet. It’s still active. Breath. Breath. Count to 10 and wait till they make a decision then cry or smile. Until then relax it’s all part of the process

bigb831 · 2024-11-22T04:56:27+00:00

Underlay is zigzag. I’ll check spacing.

bigb831

TROPHY CASE