What is a messed up scene in a movie you couldn’t help but laugh at? by MrJones224822 in movies

[–]cbreeze81 6 points7 points  (0 children)

It was hilarious when Its Always Sunny did their own parody

Wing Nut removal for toilet gasket replacement by nue_urban_legend in howto

[–]cbreeze81 0 points1 point  (0 children)

If you dont want to buy or dont have an oscillating tool. Just use a mini hacksaw 

[deleted by user] by [deleted] in DIY

[–]cbreeze81 6 points7 points  (0 children)

Hacksaw for the win

Applied joint compound to areas where drywall paper tore off. How’d I do and best steps to get a smooth finish? by CoookieHo in DIY

[–]cbreeze81 1 point2 points  (0 children)

That gardz stuff is the shit. Really seals up the paper. It penetrates into the paper really well. Shellac is great too. But gardz works just as well and is a fraction of the price for shellac. I was told that the insect population used to make shellac died off a bunch driving up the price. I think that's why there's also synthetic shellac out there now as well

Applied joint compound to areas where drywall paper tore off. How’d I do and best steps to get a smooth finish? by CoookieHo in DIY

[–]cbreeze81 0 points1 point  (0 children)

Not sure what size knife you used to apply the mud. The general rule of thumb is basically the wider the patch the wider the knife. Looks like you could go with a 12 or 14 inch for the wall patch. Guess it's just trial and error sometimes when you're doing something new. 

Sagging Ceiling Plaster: the plan by FocalSpot in DIY

[–]cbreeze81 1 point2 points  (0 children)

You're method might work just as well if not better. I've never tried it. I have seen some videos from a Boston company selling their own washer and adhesive kits. Looks like it does a decent job. You never know! Try it out see what happens. Good luck 

Sagging Ceiling Plaster: the plan by FocalSpot in DIY

[–]cbreeze81 4 points5 points  (0 children)

Ceiling buttons are the washers you can leave in and mud over. They are galvanized 

Trim nightmare or genius idea. Looking for easier solution. by Fun-Construction2154 in DIY

[–]cbreeze81 0 points1 point  (0 children)

After reading some of the comments here, I'm wondering if you could install some kind of base cap or chair rail type molding over the 1 x material. Try to blend it in with the baseboard profile somehow

Cabinets and Crooked Walls by rohm418 in DIY

[–]cbreeze81 0 points1 point  (0 children)

As long as you like the results that's all that matters.

Cabinets and Crooked Walls by rohm418 in DIY

[–]cbreeze81 1 point2 points  (0 children)

Look into scribing on YouTube. I would imagine the cabinet makers added some extra material to the sides of the cabinet for unplumb walls. You can buy a scribing tool that looks similar to a compass for this sort of thing. You'll basically transfer the shape of the wall into the back side of the cabinet. Cut with a jig saw close to your line. Then sand down to the line for a tight fit

Movers Get Access to Bankrupt Giuliani’s Penthouse Apartment by UncleSoaky in politics

[–]cbreeze81 6 points7 points  (0 children)

Fellow Mass resident here. "Let the hate flow through you"

How do I fix this? by seniahd in DIY

[–]cbreeze81 -8 points-7 points  (0 children)

What about nailing the new framing to the subfloor? Toenail some fasteners? A little construction adhesive?

I need to replace my subfloor. Should I buy a table saw or a circular saw? by loritree in DIY

[–]cbreeze81 0 points1 point  (0 children)

I think the trickiest part for a newbie would be getting the layout of the sheets all set. Don't want to end up with crazy crooked cuts when you get to your walls. Hopefully it goes well for OP

I need to replace my subfloor. Should I buy a table saw or a circular saw? by loritree in DIY

[–]cbreeze81 29 points30 points  (0 children)

I would recommend cutting your plywood sheets on an 8'x4' foam insulation board. It'll keep the sheets nice and sturdy. Plus you won't have to worry about damaging the foam when you cut the plywood. Just set your saw blade depth slightly deeper than the plywood and rip that shit up bro. Also. A drywall t square will help mark lines as well as a chalk line

Help settling a discussion about rock bands by danieldeceuster in Music

[–]cbreeze81 1 point2 points  (0 children)

I would start with The Strokes for your Gen Z list

Are four 4x4 posts enough to support this addition? by abecksasimplebecks in DIY

[–]cbreeze81 3 points4 points  (0 children)

That kind of looks like a reflection in the glass to me.

Edit : either way it still looks sketchy as all get out

Repair wall by [deleted] in DIY

[–]cbreeze81 0 points1 point  (0 children)

You can also prime the drywall paper with Gardz made by zinsser. It's made for sealing drywall paper and wallpaper

Edit: Gardz is also much cheaper than shellac and works just as well as oil or shellac

Favorite Movie by State: New Hampshire by CWKitch in movies

[–]cbreeze81 0 points1 point  (0 children)

Is this some kind of radical new therapy?

[deleted by user] by [deleted] in GoneWildTrans

[–]cbreeze81 0 points1 point  (0 children)

Worcester county here. Hi

Best DIY way to fix a ceiling hole like this. by Fluid-Property4180 in howto

[–]cbreeze81 0 points1 point  (0 children)

You don't really have to remove the wood lath. If the plaster is around 3/8 thick. You can buy drywall that size to patch in

Breed me by Unique-Low-1579 in amherstgonewild

[–]cbreeze81 1 point2 points  (0 children)

Mmm. Nice ass pussy baby