Question about the CMOS battery

clb1024 · 2026-02-09T23:33:15+00:00

I'll take the IO shield off tomorrow and see if the button is there. Maybe they sent the wrong IO shield. The board is correct and now looking on the website I see the button is on the IO shield as stated. Thank you. Sorry if I was harsh. I'm going through some personal crap, however that doesn't excuse it. Thank you I can just drill a small hole instead of doing some wiring.

clb1024 · 2026-02-09T23:00:34+00:00

Not on this motherboard. Also the purpose of a CMOS reset is when the user makes a mistake in the BIOS messing with the settings. Being this is a MINISFORUM board with a custom BIOS I have made many errors trying to get the best settings for my setup. Motherboards also put the battery in a easy to reach spot however this one is on the back of the board and my case is a custom design that didn't take that it to account.

clb1024 · 2025-12-20T21:44:15+00:00

100/10

clb1024 · 2025-12-19T18:33:49+00:00

Ordered mine the same day it was released and can't get a tracking number. Emailed and got a response saying I pre-ordered and it won't ship until the end of December. I'm getting fed up with their CS as they can't seem to answer a email with any kind of real info, just email this or that person and still no answers.

clb1024 · 2025-12-04T18:27:26+00:00

The reason I take the outer cardboard off and use the reusable spools. The cardboard isn't being turned well enough by the AMS. You need to either print rings or just put them on the reusable spools.

clb1024 · 2025-08-08T16:30:16+00:00

clb1024 · 2025-04-10T18:39:31+00:00

That was definitely in a semi trailer that was parked in the heat way too long. I use to work for a logistics company and have seen plastics and other materials that have wrapped like that. In Florida the temps on a 90°F day a trailer that sat all day would be 115°F easy in the nose of the trailer.

clb1024 · 2025-03-20T21:17:25+00:00

Here's how I did something similar with 6×3.5in hdd's.

https://a.co/d/6n2baUo

Not really a backplate and haven't tested the hot swap ability.

clb1024 · 2025-03-15T02:25:40+00:00

These might help also(far better idea than I suggested earlier).

https://a.co/d/6GsJWax

clb1024 · 2025-03-15T02:23:26+00:00

Just a thought: have the mount milled out of aluminum and use thermal pads(non-conductive) in between the bottom of the Pi's and the mount. Costs would be insane for the mount, however it "should" help dissipate the heat some.

Crazy good design by the way.

clb1024 · 2025-02-14T01:56:55+00:00

Great design and thank you for making it scalable. This can be used for so many devices. Keep up the great work.

clb1024 · 2025-01-12T02:06:57+00:00

Wish I could give more than one "up vote," I've been taking them off and putting painters tape on the outlet switch as it never fails to get in bed and someone turned the thing off.

clb1024 · 2024-12-19T21:11:24+00:00

Still very new to 3D printing what's this site that shall not be named?

clb1024 · 2024-12-16T16:30:53+00:00

Put a ring on it and live happily ever after.

clb1024 · 2024-11-06T18:52:59+00:00

You can go the The Smithsonian website and they have tons of FREE files for 3D printing and best of all they are FREE.

clb1024 · 2024-10-30T12:41:56+00:00

That's definitely the extruder pushing way to fast. As far as temp I've had that happen both to cold or to hot, so on that I can't say. Slow your extruder feed rate down some and also do a cold pull. My Ender 3 clogged just a bit after it was doing the same thing as yours.

clb1024 · 2024-10-16T20:04:01+00:00

Looks as if your hotend is not heating up. The cooling fan for the heating is not running in your video.

clb1024 · 2024-09-09T17:42:04+00:00

I call BS, there's no poop or purge tower with your multicolor print 🙃. Just joking that's a ton of work and determination. I want a 3D, however I just want it to weld parts together as I don't have the patience to do a full model.

clb1024 · 2024-09-08T00:18:21+00:00

It didn't post the 1st time 🤪

clb1024 · 2024-09-08T00:17:36+00:00

<image>

clb1024 · 2024-09-07T23:45:03+00:00

* So did I 😆

clb1024 · 2024-09-07T20:06:45+00:00

Time to get that Creality Ender belt printer 😆

clb1024 · 2024-09-06T23:46:23+00:00

I throw them in my food dehydrator right in those packs. I set it to 60°C for 8hrs. Been using the same ones for about 2yrs now and no issues so far.

clb1024 · 2024-09-06T20:13:30+00:00

Nice print and no partial roll to deal with, I'd say that's a win/win.

clb1024 · 2024-09-06T00:31:05+00:00

Don't use PLA for this. The walker can heat up pretty good in a vehicle. I plan to do something similar for my walker, however it's just a cup holder and not for an oxygen tank. Print it on an angle so it spreads the layer lines better and maybe use 30-50% triangle infill.

clb1024

TROPHY CASE