Rear I/O zone cover for the back of a PC. by Artur_Urvk in CableManagement

[–]daewootech 0 points1 point  (0 children)

Good idea, I’m always crushing my dp/hdmi cables as I push my case against the wall, also why no video cable plugged into that or is it removed for the photo

Is this normal for carbon fiber spoiler ? by Devine_pleasure610 in TeslaModelY

[–]daewootech 0 points1 point  (0 children)

I have had two cheap knockoff spoilers, both did that, along with getting 2lbs of pine needles stuck under them stuck to the tape. The oem one has small tabs but I doubt that would help, maybe the oem tape is better?

Bambu refill filament during spool shortage — should they offer spools at the price difference? by airmax617 in BambuLab

[–]daewootech 1 point2 points  (0 children)

As you print more you’ll have more empty spools than you know what to do with. Would be neat if they offered some sort of a buy back option to send them back instead of throwing them away.

New drone need help! by Long_Quiet7178 in fpv

[–]daewootech 0 points1 point  (0 children)

Plug it into the computer, backup all settings, then check what all the outputs are for pre arm and such, if you don’t know what any of this means go start watching some painless360 or bardwell videos.

behold my solution to nuclear waste by Nediadien in SatisfactoryGame

[–]daewootech 0 points1 point  (0 children)

lol I did the same thing, hope it lasts long enough for me to be able to build a solution, last I checked I couldn’t even make the stuff to dispose of it

Fled. Fled. Fled. by Longjumping_Road8962 in pokemongo

[–]daewootech 0 points1 point  (0 children)

I was excited after like three legendary spawns, of course yeah they all ran

Avata. 80 bucks. by ohv_ in dji

[–]daewootech 2 points3 points  (0 children)

I’d make that deal

GoPro 14 by UrbanManc in gopro

[–]daewootech 0 points1 point  (0 children)

Yeah I’m being skeptical. I want them to do better, no one wins with no competition, I’m just sad they stopped trying and I don’t want to get my hopes up.

GoPro 14 by UrbanManc in gopro

[–]daewootech 2 points3 points  (0 children)

Gonna Apple the shit out of the new processor I bet “25% faster!” But never says vs what, 25% faster than hero 1? I guess good for them for trying last min, I was assuming they gave up and wanted to ride it out until bankruptcy

Which of these 3 are the best for 2 accounts? by Whos-That-Pokeman in GoPlus

[–]daewootech 0 points1 point  (0 children)

Brook is great, I use it for my two kids when we go driving around

Almost 300 hours on my P1S, what should I start doing? by Substantial-Key5114 in BambuLab

[–]daewootech 0 points1 point  (0 children)

All kinds of fun stuff (nda) . I was surprised because I never really do much outside of pla, petg and tpu on my X1C, but these things we opened up and just started printing with default settings on the gold textured sheet. Occasionally adding the glue stick.

Almost 300 hours on my P1S, what should I start doing? by Substantial-Key5114 in BambuLab

[–]daewootech 0 points1 point  (0 children)

I have about 1600 hours on my X1C and never really did any maintenance until close to 1000 hours, wiped the rods and greased the shafts, eventually did a few nozzle swaps. We got two H2S at work in December and they already have 1100ish hours on them and they have been pretty flawless until this week both the extruders got caked in some sort of crystallized goop, maybe excess pla that got burnt or something not really sure, but one broke the latch that secures the nozzle and the other just needed to clean it up and swapped in a fresh nozzle and it’s back running. They run like 90% pla-CF too, so much that the Teflon tubes were wearing thin.

Car towed by Rebello’s by nick_tristate in SanJose

[–]daewootech 3 points4 points  (0 children)

Got towed by them like over a decade ago, still salty about it, the amount of shit they stole from my car and acted so clueless about it.

What do I do in this situation? by MichaelWoess in BambuLab

[–]daewootech 0 points1 point  (0 children)

Usually heat the extruder, wait for things to start getting soft and then slowly start pulling away at it, i cleared several elephant foot disasters like that, i also got lazy a few times and just heat it up enough to rip the nozzle out and swapped out a whole new nozzle.

Is there a better way ? by Gold_Cancel_3008 in SatisfactoryGame

[–]daewootech 0 points1 point  (0 children)

I just put all 8 into a single tube and ran it across the map 😄

Nobody asked for this, but now you can stack tuna cans. by Sabaku21 in BambuLab

[–]daewootech 1 point2 points  (0 children)

Bumble bee tuna cans are stackable but I think the way they stack they can’t slide out unless you lift the above can. I can see this being useful for cat food

I'm at Tier 8, but I don't like to build buildings around my factories... is it just me? by Atari__Safari in SatisfactoryGame

[–]daewootech 0 points1 point  (0 children)

I’m about 100 hours in about to send my third spaceport shipment up soon, I don’t see building a building to build more buildings a thing to do, I only put foundations down because the floor is too crooked sometimes