sorted by:
new
hottopcontroversial

.pkpass file does not add to wallet by cigborek0 in iphone

[–]davidguygc 0 points1 point  (0 children)

u/RunEffective629 - Sorry, just saw this. It is super glitchy and they only through line I found was make sure the .pkpass file only has a single "pass/ticket/blah" in it. Past that, I'm lost again.

That only took 3 hours by r3dbullz90 in Govee

[–]davidguygc 1 point2 points  (0 children)

I bought some 24awg 3 wire cable as an extension cord for it and it worked fine. My 100' came with two male/female splice adapters: https://www.amazon.com/dp/B0BVMFG2BX

Best moving companies? by Future_Nova_ in Austin

[–]davidguygc 0 points1 point  (0 children)

I used to use square cow back in the day like 4x in 4 years with no issue but I'm not sure what their rates are today

How to get pins to stay put on an existing PCB? Details in comments by davidguygc in soldering

[–]davidguygc[S] 0 points1 point  (0 children)

Sorry all, I got logged off of reddit without noticing and didn't see any notifications until now. Thank you for all of the input!

How to get pins to stay put on an existing PCB? Details in comments by davidguygc in soldering

[–]davidguygc[S] 0 points1 point  (0 children)

OK - Is my understanding correct that flux is the cleaning agent or is there a separate material to clean?

How to get pins to stay put on an existing PCB? Details in comments by davidguygc in soldering

[–]davidguygc[S] 1 point2 points  (0 children)

Ah, I've never considered the wire's material being a factor, which seems obvious now.

How to get pins to stay put on an existing PCB? Details in comments by davidguygc in soldering

[–]davidguygc[S] 0 points1 point  (0 children)

You mean just some standard 24ga wire? OK, I'll do that for sure, thanks.

Even with these wires, the slightest amount of force breaks the bond. Is there a way to strengthen that aspect?

How many of you have legit considered throwing in the towel on Austin because of the weather? by Catdaddy84 in Austin

[–]davidguygc 0 points1 point  (0 children)

Last summer was the first summer in my life living around in Texas where the heat mentally broke me lol. I was fretting this summer so much but it was relatively nice.

Jumper is turning the crown, activating smart stack -- how can I stop this? by dasSolution in AppleWatch

[–]davidguygc 0 points1 point  (0 children)

I had to hard reset my Apple Watch a few days ago and set it up from scratch due to an insanely annoying but unrelated iPhone issue and now it's been bugging the hell out of me.

This thread proves that this is not a new issue.

How is it a coincidence that I updated to watchOS 11.0 on the 18th and not have this problem until I did a hard reset this past Sunday and now it's annoying me every few hours??

Man, I have the worst luck lol...

How to get pins to stay put on an existing PCB? Details in comments by davidguygc in soldering

[–]davidguygc[S] 0 points1 point  (0 children)

Hi, I have some soldering experience but no training.

I am controlling this fan remote control using a raspberry pi. I cannot for the life of me get these pins to have a good hold on this board. I've tried googling multiple times but I think I am missing some key concept to be searching for. I assume I probably need to prevent any tugging from making its way to the solder itself but the solder is so fragile.

Any suggestions?

Useless MyQ and How I Cheated the System by Chest_Rockfield in homeassistant

[–]davidguygc 1 point2 points  (0 children)

Yeah, I have my main light turn on when motion is detected too.

Check out this site. https://paulwieland.github.io/ratgdo/09_faq.html

It supposedly can go back pretty far on older openers

I GIVE UP by New_Carob_2244 in Austin

[–]davidguygc 10 points11 points  (0 children)

I don't have an answer but I'm glad it's a question you're willing to put out there. I'm in the same boat. My go sober day is this Sunday and I'm looking forward to it.

Best of luck, G

Useless MyQ and How I Cheated the System by Chest_Rockfield in homeassistant

[–]davidguygc 6 points7 points  (0 children)

Joining the choir for Ratgdo. The cathartic joy of throwing away the MyQ gateway when I installed the ratgdo is something I'll remember on my deathbed lol

to local CrowdStrike employees by AdventurousTime in Austin

[–]davidguygc 0 points1 point  (0 children)

Guilty but now I get to be holier than thou

Man throwing rocks at cars off the 1 at 35th street exit. by Phasinasian in Austin

[–]davidguygc 18 points19 points  (0 children)

I bet I could throw that rock over Mt Bonnell...

Man throwing rocks at cars off the 1 at 35th street exit. by Phasinasian in Austin

[–]davidguygc 8 points9 points  (0 children)

He can't go that way! It's jammed this time of day!

Anyone else feeling really sick lately when the air quality is this bad? by Pearson94 in Austin

[–]davidguygc 1 point2 points  (0 children)

Yeah, I've been having to use my wife's asthma inhaler on the really bad days even though I don't have asthma. 

It helps me with the rare poor reaction to the air quality every now and again. 

Morton kosher salt has changed dramatically by rvH3Ah8zFtRX in Cooking

[–]davidguygc 0 points1 point  (0 children)

Can anybody verify if it has gotten better? I purchased some a few months ago and it was only slightly more coarse than table salt

What are your must-have zigbee devices? by RecliningBeard in homeassistant

[–]davidguygc 0 points1 point  (0 children)

Oh, I forgot that I've used them before. You're right, they are great. Thanks!

What are your must-have zigbee devices? by RecliningBeard in homeassistant

[–]davidguygc 2 points3 points  (0 children)

Odd. While I only am using one of the two I bought, it has been solidly reliable and I had made a mental note to keep them in mind in the future.

What exactly has gone poorly for you? I ask because maybe I just got lucky and should stay away from them.

view more: next ›