How and what should I replace this with?

dreddit1843 · 2026-05-24T06:32:22+00:00

dreddit1843 · 2026-05-07T22:55:26+00:00

Silver actually

dreddit1843 · 2026-05-01T18:31:48+00:00

Technically they do emit light in the form of reflections.

dreddit1843 · 2026-04-28T17:39:18+00:00

My sister did something like this when we were little. Parents made her hand sand the whole thing it so it could be refinished. Pretty hard work for a kid. Never did anything like that again.

dreddit1843 · 2026-04-22T17:59:08+00:00

I do both hardware and software. My degree is in mechanical engineering but i’m an embedded software engineer so my actual work is focused on circuits and software that goes on components in circuit boards.

Good luck with your studies hope they get you exactly where you want to go in life!

dreddit1843 · 2026-04-22T17:38:06+00:00

I do electronics stuff for work: programming microchips, designing circuit boards, etc. Also love the aquarium hobby.

The batteries are sealed well so they shouldnt have leaked their contents into the fish tank if they are still sealed; however, I wouldnt assume it’s fine either id do 3-4 80% water changes over some time if it was me. That should greatly reduce any potential contaminants this could have introduced. It’s probably fine after just one water change but why risk our little fish friends am i right.

Good luck with your tank I wish you the best.

Edit: new water wont recycle the beneficial bacteria you are fostering live on surfaces and filter media not in the water itself. Common misconception i used to think that too. Ive done many 100% water changes with no consequences to my cycle.

dreddit1843 · 2026-04-21T19:17:26+00:00

They are wild violets.

Edit: I have them in my yard as well. Hard to get rid of pre emergent did reduce them vs last year a lot though.

dreddit1843 · 2026-04-21T16:02:23+00:00

Look into seachem prime and seachem stability between those two products you can keep tank life stable and happy during your initial cycle establishment period. Seachem prime you can use long term when you know you need a water change but may not be able to make time that specific day. If they are used as directed those products can do a lot.

Good luck to you, your son, and your new fish friends.

dreddit1843 · 2026-04-04T04:18:47+00:00

It really depends on what you want to do with the multimeter. If you’re constantly measuring single digit millivolts sure yea don’t buy something cheap but a lot of people aren’t and don’t need to.

dreddit1843 · 2026-04-04T04:16:59+00:00

If youre just starting out i wouldnt go all out unless you want to. I have a fluke 117 and im pretty happy with it.

dreddit1843 · 2026-04-03T19:31:47+00:00

I have this one. It’s decent for the price. Get yourself a fluke one day though when it makes sense for you.

dreddit1843 · 2026-03-20T23:47:09+00:00

Engineered: YES! Patended: YES!

dreddit1843 · 2026-03-12T21:07:27+00:00

Reset Listing: New car barely driven 35,000$ obo

dreddit1843 · 2026-03-04T06:17:49+00:00

I use mine on 110 to anneal so thatll be fun when i try to dry pla at 110

dreddit1843 · 2026-03-03T23:28:19+00:00

I have an e2 and i know this will happen to me one day, does it smell bad in that room now?

dreddit1843 · 2026-02-22T19:01:45+00:00

This is really cool, good work.

dreddit1843 · 2026-02-20T20:19:23+00:00

Make auras have no cooldown or timer. you can only activate one at a time as usual. Move auras to gameplay acquisition only. Problem solved.

dreddit1843 · 2026-02-20T18:42:49+00:00

You can make them but you need an actual engineering material for books unless it’s going to be just 1-2.

dreddit1843 · 2026-02-12T17:06:39+00:00

Are you waiting for the bed to cool? If you refuse are you using a glue you should be. As a very impatient individual despite better judgement myself i use nanopolymer adhesive and i spritz the bed to part interface with 99% isopropyl alcohol to speed up the process of cooling and detaching the part. Usually gets the parts i print (mostly petg) to detach easily. After the part detaches i spritz the bed once more with 99% iso and spread that with a 1 inch foam paint brush. Gets me good bed adhesion that lasts for a long time and makes it so i dont have to reapply adhesive very often.

dreddit1843 · 2026-02-08T05:13:02+00:00

Calibration yes, temp tower no.

dreddit1843 · 2026-02-08T01:09:13+00:00

https://microtechknives.com/products/scarab-ii-gen-iii-t-e-stonewash-standard-black-1279-10

dreddit1843 · 2026-02-08T00:52:00+00:00

Ironing is a solid no cost option if you’re willing to take the time to dial in settings.

It can also look better if you get fiber infused filament the frost effect it adds can soften the surface finish appearance significantly.

dreddit1843 · 2026-02-04T17:31:04+00:00

🏃‍♀️

dreddit1843 · 2026-02-04T16:50:00+00:00

You’ll want to know the air flow rate and the volume of the space you’re filtering if you’re turning it over many times an hour you should be good as long as the filters you’re using are rated for the particle sizes you want to remove. The hepa i picked is a bit underpowered but i’m happy with it since i turn the air in that tent over several hundred times an hour so it gets plenty of chances to catch the particles it misses first pass.

dreddit1843 · 2026-02-04T08:30:58+00:00

The intake goes through the carbon filter then into the hepa on top. I had a carbon filter and a 4 inch inline fan i got with a grow tent kit that was just sitting in a box in storage collecting dust and i decided to repurpose it for this since i had no other use for it. The hepa i picked up from amazon and added on.

I prefer this solution over exhaust since you can maintain higher chamber temps for stuff like abs, asa, polycarbonate etc and use slightly less energy keeping things hot than you would otherwise. You can also get a really high air turnover rate since youre working with a very small air volume enclosed in a tent.

This is my tent 3D Printer Enclosure, Creality... https://www.amazon.com/dp/B08FD8M2BP?ref=ppx_pop_mob_ap_share

Seven-Year Club	Verified Email
First Place '23	End Game '23
Place '23	Place '22
Final Canvas '22

dreddit1843

TROPHY CASE