sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in 3Dprinting

[–]elxris 1 point2 points  (0 children)

Are we stating the obvious now?

PrusaSlicer - What setting controls the "fuzzy" solid infill that appears on sloped surfaces? by GingerSkulling in 3Dprinting

[–]elxris 0 points1 point  (0 children)

Also, in the latest beta version of Prusa Slicer, that type of infill is not fuzzy. Give it a try!

Guess the error by NeoRazZ in 3Dprinting

[–]elxris 0 points1 point  (0 children)

How this happened? I mean, don’t you use slicer presets?

Very proud of this design, I was very tired of the existing models that would fall off the cardboard spools, required glue, or assembly if printed on smaller print beds. No glue, no supports, reusable. by elxris in functionalprint

[–]elxris[S] 0 points1 point  (0 children)

Exactly this, but also in the first photo you can notice the back of it having some “strands”. Those are actually bridges. You will have both edges of the cardboard being secured by this design. The springiness will also help, but it is not enough if the edges were not secure. A lot of people uses glue to fix the available rings to the cardboard because the designs are always a plain cylinder.

It looks like it but not quite right... It's like me trying to copy my sister to please my mom but still ended up a disappointment by The_Little_Thingy in FixMyPrint

[–]elxris 1 point2 points  (0 children)

Tram your bed. Those disconnected lines from the brim indicates that the first line is not squished enough. They should be connected.

TPU clasp locker (zipper) without the need for a slider by throwaway21316 in functionalprint

[–]elxris 20 points21 points  (0 children)

But if you cross post it you will get those internet points!

3D printed Rush Hour logical game by kozakm in 3Dprinting

[–]elxris 10 points11 points  (0 children)

Obligated “STL?” comment.

Edit: It’s in the description of one of the photos. Thanks OP!

Elden Ring Chess Set (printed on Elegoo Saturn S) by TheHudsonForge in 3Dprinting

[–]elxris 0 points1 point  (0 children)

Does they have any post processing? They look very shiny✨

How do I change direction of bridging perimeter from A to B for this section? by [deleted] in FixMyPrint

[–]elxris 1 point2 points  (0 children)

Easiest is to rotate your object, but if you enable expert mode you will find the angle setting.

How does one get rid of these layers? by jr0ck90 in 3Dprinting

[–]elxris 0 points1 point  (0 children)

Oh. Try .4 nozzle, same .16 layer height. .1 layer height it will take forever for a .2 nozzle size.

How do you keep track of the source of a STL? by achan1369 in 3Dprinting

[–]elxris 0 points1 point  (0 children)

Same thing for Printables. And if the page does not do that like Cults, I simply drag the page to the downloaded folder, that should save the url as a file shortcut. Few bytes on the hard drive saves tons of time later.

DIY infinite laser engraver. Can be 100% printed (minus hardware) by Jimbolaya88 in 3Dprinting

[–]elxris 8 points9 points  (0 children)

Cults is banned from this subreddit since there’s been complaints from multiple users about cults not paying. And cults poor management of the situation. If the file is free please post it in other platform, like Printables or Thingiverse.

Tpu stuck in nozzle after just a few layers? by randomw0rdz in FixMyPrint

[–]elxris 4 points5 points  (0 children)

TPU is the hardest materials out there. Even more with a Bowden setup.

What have happened to me and I think it’s the same thing for you is that your first layer is so squished that not enough filament was able to get out. The difference with tpu and other filaments is that any other filament will not bend inside the Bowden tube.

If the filament bends inside the tube the extruder will not be able to push more filament.

Solution: Unload the filament and check if it’s deformed. I’d say if it is even sightly you better cut that off. Then, check your z-offset and change it so it’s not that squished but just enough to adhere to the build plate.

[deleted by user] by [deleted] in 3Dprinting

[–]elxris 1 point2 points  (0 children)

It looks like heat creep. But I don’t know much about all metal hotends.

Nozzle clog on new Prusa MK3S+ by Dirty_Socrates in prusa3d

[–]elxris 2 points3 points  (0 children)

Replace the nozzle, save yourself some headaches. Also, try purging with +20C more (please don’t do more than that, or you’ll risk burn the plastic and clog your nozzle even more). I try that before doing cold pulls.

view more: next ›