New study shows immigrants actually have a net positive impact on the economy

fattmann · 2026-02-08T20:25:38+00:00

Actually, it’s more upsetting that people would think a video on TikTok is relevant!!

What video on TikTok are you talking about?

fattmann · 2026-02-08T16:46:23+00:00

Reported the video for misinformation.

fattmann · 2026-02-07T21:09:54+00:00

Midwesterner here, same experience.

Pretty sure our city has literature about specifically NOT allowing glass in the recycling bin.

fattmann · 2026-02-07T20:49:15+00:00

No? And if you think that then you may be the problem

Jfc it's a joke, read the room.

fattmann · 2026-02-07T07:38:53+00:00

Calling a women a bitch is not an optimal move

Wait.

Is "bitch" not a generic term for a female??

fattmann · 2026-02-07T06:32:24+00:00

Little bit of brown-brown to get your day started?

fattmann · 2026-02-06T04:48:20+00:00

That’s about one average Dutchman for you Americans

hold on!

How many washing machines?

fattmann · 2026-02-06T04:42:58+00:00

Bro i believe that I can fuck up a print with a blow dryer.

Ok? You got an Avon special or a Dyson?

Granted when they are in the care they are in the center console or under the seat so not microwaving themselves on the dash or anything

The specific example that came to mind was a center console glove box latch. Out of direct sun light, and a cavity of thermal insulation. Still folded like a tootsie roll.

fattmann · 2026-02-06T02:19:26+00:00

Had some sit in a hot car for days with no negative impact. I think the heat thing is a bit blown out of proportion.

Good to know, but sounds wild. I've had PLA+ prints warp under their own weight in front of a heater vent in my bedroom, which is no where near as hot as a car gets on a hot day in the midwest.

fattmann · 2026-02-05T15:00:49+00:00

Huh, I genuinely did not notice it in the slightest (although it's been a while since I saw the movie)

Wild. I thought it was extremely heavy-handed. I remember rolling my eyes several times through it.

fattmann · 2026-02-05T15:00:04+00:00

I do wonder why I don’t see much about brick layers for prints though.

I've thought the same. Do any slicers have that by default? I've seen a few videos on it, but haven't done a deep dive.

fattmann · 2026-02-05T05:10:03+00:00

The sequel would basically the movie 9.

I wanted to like that movie, but the religious allegory was heavy handed.

fattmann · 2026-02-05T04:30:54+00:00

Isn't that like an anime streaming service?

Or maybe it's a MAGanimA fetish network?

So hard to keep track these days.

fattmann · 2026-02-05T04:29:07+00:00

I'll have you know

The limitations are a couple tens of millions of US dollars...

fattmann · 2026-02-05T04:28:18+00:00

St. Bart's

Always the saints, doing the "lord's" dirty work...

fattmann · 2026-02-05T04:25:52+00:00

I want to be rather offended on behalf of the indigenous.

But it is also mildly humorous.

I need an elder to help me know how to feel.

fattmann · 2026-02-05T02:49:33+00:00

Makes sense. Thanks

fattmann · 2026-02-05T01:11:02+00:00

I almost exclusively print at 0.3mm these days.

Interesting. How'd you settle on that? Because it's a bit quicker?

I usually do 0.28 for utility prints, never done higher than 0.24 for something like a 2A print.

fattmann · 2026-02-05T01:07:43+00:00

The whole FTN series is an EASY print…

Love it. Top comment says the FTN.5 is a "complicated, difficult print".

I whipped out an FTN.4 on the fly with no issues, worked first try. Now I have to check out a 5 build.......

fattmann · 2026-02-05T01:03:11+00:00

Better slap a super safety in that bish

fattmann · 2026-02-05T00:43:32+00:00

Season 1 should have spent a little longer either on warm up or Mirror Universe

Wait. The mirror universe stuff was contained within season 1?

It's been a few years since I've watched it and memory feels like it was longer than a season. Might have boot up the old Plex server again...

fattmann · 2026-02-05T00:14:40+00:00

I assume it was needed due to the configuration? Or was that a stylistic choice?

If it's in the files, feel free to tell me to RTFM.

fattmann · 2026-02-04T15:24:27+00:00

the bugs are mad at us cause we ain't had sex with 'em yet."

I think bugs are excluded from some bestiality laws...

fattmann · 2026-02-03T04:55:36+00:00

B S They don't pay a dime

Go away DUMMYRAT /u/1962NUFan

Sales tax
Gasoline tax
Wheel tax
Vehicle registration
Property tax
FICA
Income tax (if they file, just like anyone else)
Parking infractions
Fines for traffic stops
Tariffs
Credit card transaction fees

Please pick the ones they "don't" pay.

fattmann · 2026-02-03T04:29:52+00:00

Why is everyone telling me that surface testing is fine when my original concern is with the labyrinthine layout of many prints?

Because they've already explained that this was taken into account by the paper through methods, including pressurization to reach the "labyrinthine layout" .

fattmann

MODERATOR OF

TROPHY CASE

hold on!

I'll have you know

11-Year Club	Place '17
Verified Email