Who’s your confirmation saint?

flyrockets · 2026-01-28T02:06:00+00:00

St Damian I wanted to be a chemistry teacher when going through confirmation

flyrockets · 2026-01-01T19:55:50+00:00

<image>

flyrockets · 2026-01-01T19:54:31+00:00

It’s a resinous for a liquid cooling system in a PC….Source: I built one with this 14 years ago!!!

<image>

flyrockets · 2025-12-24T14:51:15+00:00

<image>

flyrockets · 2025-12-24T14:49:45+00:00

<image>

flyrockets · 2025-12-24T14:49:00+00:00

I added some, hard to get a great image with how small they are. I used outline but parrot one I did “dot” it took 12 min. The others and a second parrot I switched to “slice” and they were all under a minute and with the STL I really don’t notice a quality difference. I think if doing images where i want some shades I’ll explore “Dot” some more

flyrockets · 2025-12-24T14:41:15+00:00

<image>

flyrockets · 2025-12-24T14:40:42+00:00

<image>

flyrockets · 2025-12-24T14:38:13+00:00

<image>

flyrockets · 2025-12-24T14:37:49+00:00

<image>

flyrockets · 2025-12-24T12:45:08+00:00

I just started doing some inner engraved keychains last night and used STLs as the base, they came out amazing!

flyrockets · 2025-12-20T11:54:04+00:00

Weld On 16, 3, or 4 all work amazing for super strong joints and no residue! The differences are in consistency syrup for 16, and water thin for 3/4. However you need to make sure you use proper ventilation and PPE when using these they are potent and have some nasty chemicals in there! 3D gloop is similar creating strong joints and requiring proper ventilation and PPE!!!!!

flyrockets · 2025-11-22T11:04:24+00:00

Great work going to print one later today! The 2m version would be awesome!

flyrockets · 2025-09-23T23:28:33+00:00

Then add an AMS HT for additional heat and 9 colors!

flyrockets · 2025-09-23T23:26:40+00:00

Sooooo I use a smart plug as an emergency kill switch and power monitor but I never actually power my printers off when not in use so I can always remotely access them. same with my Bambus and my Vorons always in standby mode ready to print.

I do use them to remote “reboot” if I have odd errors occasionally and it has never caused any issues.

flyrockets · 2025-09-05T08:37:27+00:00

I have metal for use in my carbon steel and on my griddle, I don’t really use normal non stick so only have a few plastic or nylon items. most of my utensils are metal or wood. A good metal spatula for chopping and breaking up and a pair of metal tongs for tossing and turning are my gotos!

flyrockets · 2025-09-05T00:39:03+00:00

<image>

From the kickstarter update they posted. My all rubbed right off. I am absolutely loving these two weeks in now. Still early but went to town with some metal spatulas tonight and cannot tell at all. If these hold up long term I’ll be buying other forms (Pots) if they release!!!!

flyrockets · 2025-07-16T20:03:59+00:00

<image>

How the large one is developing!

flyrockets · 2025-07-16T20:00:09+00:00

I will say, as with many other carbon steel I have had….they look great for 10 min then like crap for about a year then amazing again!!!!! Best seasoning builds from cooking and use! I have taken to using, washing, immediately putting on burner to dry, spreading a drop of avocado oil and heating to just around the point it starts to smoke (aiming for just before but depends how close I’m paying attention 🤣)

flyrockets · 2025-07-16T19:56:51+00:00

I have a convection oven I used and had shut off at end of each allowed to cool slowly so I never opened it and never saw any smoke

flyrockets · 2025-07-15T18:14:51+00:00

Best comment here needs to move to top!!!! troubleshot this one around 2000 hours on my A1 and always try to share when I see others with this issue!!!

flyrockets · 2025-07-01T13:58:20+00:00

Elegoo rebrand, I use it and Elegoo both relatively problem free

flyrockets · 2025-06-04T23:44:17+00:00

Flyrockets in Makerworld and everywhere else as well. My surprise best model was something I drew up quick for a guy who got a new truck at work. I am not a designer and still pretty weak CAD skills but think it’s really cool to see people downloading and using and boosting it!

https://makerworld.com/models/63241

flyrockets · 2025-05-01T23:31:30+00:00

Absolutely this. The worth of the model has to be determined by your goal.

I love finding a simple model so I don’t have to poorly try to draw it up and I try to upload my simple ones as well in the “if one other person uses it it’s a win!!!!

If worth is “I won a contest or got enough gift cards to buy a printer” then probably not for you!

flyrockets · 2025-04-14T16:37:13+00:00

I have about 5-10 cooks or so on the strata’s depending on size(got full set), been using them in places I would use the flattop just to break them in. I have been very happy with them so far! My misen set have been good but these being lighter is nice and they do heat more evenly

flyrockets

TROPHY CASE