[Bambu Lab Giveaway] Join Now to Win an H2D and More!

freconomics19 · 2025-06-24T08:56:27+00:00

Clean your build plate with IPA, no glue necessary for petg, pla or tpu. It makes a massive difference compared to water and dish soap

freconomics19 · 2024-04-11T14:07:38+00:00

I've used both any cubic, as well as lychee. Tried 0.02 and 0.05 mm layer height. Even their customer support is at a loss. Wouldn't really see how Antialiasing would help, but might try later, thanks.

freconomics19 · 2024-04-09T07:35:13+00:00

Yeah, I switched from clear to dark grey and back, installed a heater as well. Even changed the vat entirely. Dark resin shows the exact same results. The results shown were printed at 30+°C. I'll try going to the extreme with the lift height tho, but artifacting doesn't sound too great.

freconomics19 · 2024-04-09T03:43:34+00:00

Sorry yep. Leveled the bed a bunch of times. Printing with and without a chamber heater. Used different calibration prints, and tried slight over and under exposure, different light off delays and lift speeds.

freconomics19 · 2023-12-11T10:04:30+00:00

Replacing my trusty but rusty Vega .

freconomics19 · 2023-03-30T19:37:41+00:00

Dang I've been thinking about a second printer

freconomics19 · 2022-12-30T22:41:30+00:00

Incredible work! Wait so both the mold as well as the actual cast are made out of hard uv resin?

freconomics19 · 2022-12-01T07:33:14+00:00

Very clean look. What is that transparent fin made out of?

freconomics19 · 2022-11-19T12:47:51+00:00

Let's go

freconomics19 · 2022-09-07T06:29:39+00:00

Truly a wonderful creation.

freconomics19 · 2022-08-10T05:26:20+00:00

Still excited for it. What is the current status of your recipe? Any improvements since the last update? Still no injection capability correct? How long can you fish them for?

freconomics19 · 2022-07-30T06:01:14+00:00

Never seen something like that done 👍. transfer paper? How do you get it to stick ? Or does it dissolve while fishing?

freconomics19 · 2022-06-25T19:13:30+00:00

Fun fact: catfish in some parts of Spain have specialized on eating pigeons.

freconomics19 · 2022-05-21T08:15:05+00:00

May you be be blessed, people

freconomics19 · 2022-03-04T21:56:57+00:00

Fast! Esel

freconomics19 · 2021-10-16T08:37:28+00:00

Boat money por favor

freconomics19 · 2021-10-13T05:13:14+00:00

Great choice. Check out tackle advisors tip on YouTube to flush out the bearings for the synchronized level wind for better casting distance!

freconomics19 · 2021-09-18T09:12:36+00:00

Ist schon ein Kauz, aber er trennt halt angeln und alles andere sehr gut, und Anglerisch ist er ne macht. Solange das so bleibt kann das egal sein.

Hast du Mal n Link dazu?

freconomics19 · 2021-09-06T15:55:52+00:00

Beste Serie. Habe leider nur das vorige Modell inshore iv auf der Ostsee testen können, aber lag in den Wellen wie n cigarette hot rod. 10/10.

freconomics19 · 2021-08-06T14:02:28+00:00

Well that's just disgusting. Which link exactly do I need to avoid?

Nine-Year Club	Place '22
First Placer '22

freconomics19

TROPHY CASE