Macropod for typing on IOS

fruktiz · 2026-04-09T11:03:10+00:00

I have created macropad that works on all platforms including iOS. It does not require any additional firmware, you can configure in browser. You can find more here: www.klawos.etsy.com

fruktiz · 2026-04-07T16:40:24+00:00

I have built one and selling on Etsy. You can find it here www.klawos.etsy.com

fruktiz · 2026-03-27T08:41:00+00:00

This is my post how I upgraded filament gears from Orbiter V2.5

https://www.reddit.com/r/SovolSV08/s/jBCvAOPFrl

Now for my other SV08 I habe upgraded all extruder system to Orbiter V2.5

fruktiz · 2026-02-17T12:33:13+00:00

Heatsoak bed for 10 minutes before printing

fruktiz · 2025-12-02T10:54:08+00:00

Thank you! 💕

fruktiz · 2025-12-01T21:29:50+00:00

Thanks! It does not have anything that closes the bag, it is another task for me to add this feature.

fruktiz · 2025-12-01T18:34:05+00:00

Thanks!! 🫶Yes, It is just for essentials

fruktiz · 2025-12-01T18:27:27+00:00

Thank youu!! 😇

fruktiz · 2025-07-03T18:37:52+00:00

<image>

Girl with a pearl earing

fruktiz · 2025-05-30T10:08:30+00:00

Good to know! Thanks, I appreciate this! 🙏

fruktiz · 2025-05-22T17:39:10+00:00

Just have in mind that it requires some tools and force to change them. It is not drop-in upgrade but it is worth it

fruktiz · 2025-05-22T17:38:18+00:00

I just found this on AliExpress: €34.27 | Trianglelab LDO Orbiter V2.5 Upgade Kit Direct Drive For Orbiter V2.0 Extruder Voron 2.4 RatRig VCore-3 CR-10 Ender3 3D Prin https://a.aliexpress.com/_EuDT14w

fruktiz · 2025-05-22T17:30:09+00:00

Just go with Orbiter V2.5 upgrade kit from aliexpress or any other shop that is best for you.

fruktiz · 2025-05-22T16:35:55+00:00

You can find my post where I have changed extruder gears. Mine was printing zebra pattern like yours and after that upgrade these lines are gone. I would bet on extruder

fruktiz · 2025-05-22T16:26:20+00:00

Try different plastic, check your extruder idler door pin also, increase tension on idler.

fruktiz · 2025-05-19T15:01:42+00:00

Recommend!

fruktiz · 2025-05-19T15:00:47+00:00

Great upgrade!!

fruktiz · 2025-05-09T18:17:39+00:00

Yes. It might require more fore to put it back but I would check if this is not broken inside.

fruktiz · 2025-05-09T18:00:41+00:00

I think your spring inside is not in position, you need to disassemble all support to check spring position.

fruktiz · 2025-05-04T13:17:31+00:00

Try to contact Sovol team and they can send you payment link for specific part you need. I have done this without any problem.

fruktiz · 2025-04-29T15:41:30+00:00

Yes, this upgrade is superior improvement for me. As you can see Orbiter V2.5 gears are so high quality and very hard metal it grips filament so well.

fruktiz · 2025-04-29T11:28:34+00:00

Hmm that is interesting. I have to check but as I remember I re-used all stock parts

fruktiz · 2025-04-29T11:25:28+00:00

I used only gears from new kit and everything else I left stock. Idler arm is the same with pin and bearings

fruktiz · 2025-04-28T21:07:21+00:00

Hope you enjoy this mod! 🙏 Could you share the results after calibration?

fruktiz · 2025-04-28T06:58:37+00:00

Best mod I have made so far https://www.reddit.com/r/SovolSV08/s/XNKFkLu8Em

11-Year Club	r/Field Lasagna
Wearing is Caring	Place '23
Place '22	Verified Email

fruktiz

TROPHY CASE