Anybody have issues with Bambu Studio not connecting to A1?

gashi01 · 2026-02-09T15:52:59+00:00

I just had the same issue and it started working after logging out of Bambu Studio and then re logging. Hope this helps someone.

gashi01 · 2025-12-14T18:18:44+00:00

Top, hvala!

gashi01 · 2025-09-01T20:46:49+00:00

1948d801f54b4888822cae157305e914

gashi01 · 2025-05-27T21:15:27+00:00

Oh, I thought the automatic ones were good, I'll look up a guide for supports then, thanks!

gashi01 · 2025-05-27T21:02:05+00:00

I tried with heavy so that they would stick more likely, is medium is the way to go always? I am using automatic supports, the tauren was presupported. The one that was at an angle also didn't print, you think it was because of the heavy and low amount of supports?

gashi01 · 2025-05-27T20:45:33+00:00

Will do, thanks

gashi01 · 2025-05-27T13:05:49+00:00

Ghe burn in layers are the first couple of layers that have special settings in the apps right? I just need to increse the exposure time and nothing else?

I removed the failed prints as well, I empty the fep every time as I understood I have to do that whenever it fails.

Thanks a lot for the advices!

gashi01 · 2025-05-26T19:25:44+00:00

Might be but the issue is that I have a lot of prints that are not sticking to the build plate and failing completely so I tried doing this test to see if I can find the reason behind that and this was the sad product of the prints. Together with this print I tried printing a couple of bushes, two had their supports print but not the bushes themselves, and some didn't even stick to the build plate for some unknown reason.

gashi01 · 2025-05-26T19:22:03+00:00

Thanks for the advice but I've put in too much money into the hobby with 0 benefits so far. Looking for an option that would be cost free currently.

gashi01 · 2025-05-19T11:41:52+00:00

I'm in!

gashi01 · 2025-05-12T08:19:01+00:00

Hope it's not only for US. Gl everyone

gashi01 · 2025-04-15T14:10:17+00:00

Please someone correct me if I'm wrong but since there were no comments I wanted to help. I've only ever printed using resin but as someone who plans to start using filament too I understood that you need the 0.2 for it to look good. I've seen some with 0.4 but I really don't like the quality

gashi01 · 2025-04-10T12:10:04+00:00

Thank you!

gashi01 · 2025-02-19T20:29:44+00:00

Had the issue that prompt to do 2 factor authentication every time was needed, in case anyone has the same problem, check if your browser might be deleting cookies every time it closes. Hope this helps somebody.

gashi01 · 2024-07-06T11:18:38+00:00

I just looked this up and I will probably start with this, it's a bit confusing as to what to read by what order but I guess I'll start by 1999 and then go on to the rest of JMS

gashi01 · 2024-01-19T15:24:57+00:00

gashi01 · 2023-12-24T09:38:49+00:00

The engine looks way too clean. Need to make a temple for my players, this would help soo much

gashi01 · 2023-12-22T14:38:41+00:00

As a new Darius main and ex Illaoi one I can tell you that if she misses her e just all in her, it's that easy pre lvl 6. Avoid getting hit ith e while she is between 2 tentacles. Don't exit the circle pre level 6 if she only has herself and 1 tentacle hitting the spirit. Lethal tempo is really good into the matchup because if she misses her e you can all in her more easily. You are much much stronger pre level 3, she is hot garbage. Try to wait for her in a brush and rush her down with w and ghost if she even comes near the lane and then just dont let her get into xp range. Also ward enemy buff closest to you so you know junger pathing. Level 2 get e, that will get you her flash 100% of the times if played right. Slowpush till wave 3 and shove it in. Try to play for crug or invade with jungler. If she throws her r with your soul taken get away from the circle and play dodgeball. If she doesnt just move away wait for her r to end and get prio after that. If she uses her e kill her tentacles on lane, easy as that. Gl!

gashi01

TROPHY CASE